网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）
- A、1
- B、10
- C、1562
- D、64000
- E、128000
- F、None of the above
参考答案
更多 “If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）A、1B、10C、1562D、64000E、128000F、None of the above” 相关考题
考题
How is the cost of a virtual link in OSPF calculated?()
A. Takes the metric of the outgoing interface.B. Uses the metric that is assigned during configuration.C. Uses the path metric to reach the virtual link neighbor.D. Uses a default of zero unless otherwise specified.
考题
In JUNOS software, what is the default interface metric for IS－IS?()
A.1B.10C.100D.10^8/link bandwidth
考题
When configuring OSPF on the ERX, what is the default auto－cost reference－bandwidth value?()
A.AB.BC.CD.D
考题
The following output was taken from Router R3. A scan of R3‘s configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（）R3show ip ospf interface briefInterface PID Area IP Address/Mask Cost State Nbrs F/CSe0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A. An a uto - cost reference - bandwidth 1000 command in router ospf modeB. An auto - cost reference - bandwidth 2000 command in router ospf modeC. An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD. An auto - cost reference - bandwidth 64700 command i n router ospf mode
考题
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG.For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A. When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B. When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C. When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D. When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E. None of the other answers is correct.
考题
What is the default metric used on IS －IS routers for each interface?()
A. The cost is set to 10 for all interfaces.B. The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C. The cost is based on the speed of the interface.D. The cost is based o n a composite of bandwidth and delay of the interface.
考题
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?()
A.1B.10C.1562D.64000E.128000
考题
If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?()
A. 1B. 10C. 1562D. 64000E. 128000F. None of the above
考题
Your network trainee asks you, in the context of IPv6 and OSPF, what best des cribes a type 9 LSA? What should you tell her?()
A. Link LSAB. Interarea prefix LSA for ABRsC. Router LSAD. Switch LSAE. Intra - area prefix LSAF. None of the above
考题
If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?()
A. 1B. 64C. 1562D. 64000E. 1500
考题
Open Shortest Path First (OSPF) was designed as an （ ） gateway protocol, for use in an autonomous system such as a local area network (LAN). It implements Dijkstra's algorithm, also known as the （ ） path first algorithm. As a link-state routing protocol it was based on the link-state algorithm developed for the ARPANET in 1980 and the IS-IS routing protocol. OSPF was first standardised in 1989 as RFC 1131, which is now known as OSPF version 1.Routing protocols like OSPF calculate the shortest route to a destination through the network based on an algorithm. The first routing protocol that was widely implemented, the （请作答此空）, calculated the shortest route based on hops, that is the number of routers that an IP packet had to traverse to reach the destination host. RIP successfully implemented dynamic routing, where routing tables change if the network topology changes. But RIP did not adapt its routing according to changing network conditions, such as data-transfer rate. Demand grew for a dynamic routing protocol that could calculate the fastest route to a destination. （ ） was developed so that the shortest path through a network was calculated based on the cost of the route, taking into account bandwidth, delay and load. Therefore OSPF undertakes route cost calculation on the basis of link-cost parameters, which can be weighted by the administrator. OSPF was quickly adopted because it became known for reliably calculating routes through large and complex local area networks.As a link state routing protocol, OSPF maintains link state （ ）, which are really network topology maps, on every router on which it is implemented. The state of a given route in the network is the cost, and OSPF algorithm allows every router to calculate the cost of the routes to any given reachable destination. Unless the administrator has made a configuration, the link cost of a path connected to a router is determined by the bit rate (1 Gbit/s, 10 Gbit/s, etc) of the interface. A router interface with OSPF will then advertise its link cost to neighbouring routers through multicast, known as the hello procedure. All routers with OSPF implementation keep sending hello packets, and thus changes in the cost of their links become known to neighbouring routers. The information about the cost of a link, that is the speed of a point to point connection between two routers, is then cascaded through the network because OSPF routers advertise the information they receive from one neighbouring router to all other neighbouring routers. This process of flooding link state information through the network is known as synchronisation. Based on this information, all routers with OSPF implementation continuously update their link state databases with information about the network topology and adjust their routing tables.OSPF has become a popular dynamic routing protocol. Other commonly used dynamic routing protocols are the RIP and the Border Gateway Protocol (BGP). Today routers support at least one interior gateway protocol to advertise their routing tables within a local area network. Frequently implemented interior gateway protocols besides OSPF are RIP, IS-IS, and the proprietary Interior Gateway Routing Protocol (IGRP) by Cisco.A.OSPF
B.RIP
C.IS-IS
D.EIGRP
考题
Your network trainee asks you, in the context of IPv6 and OSPF, what best des cribes a type 9 LSA? What should you tell her?（）A、Link LSAB、Interarea prefix LSA for ABRsC、Router LSAD、Switch LSAE、Intra - area prefix LSAF、None of the above
考题
If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?（）A、1B、64C、1562D、64000E、1500
考题
The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1A、An a uto - cost reference - bandwidth 1000 command in router ospf modeB、An auto - cost reference - bandwidth 2000 command in router ospf modeC、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf modeD、An auto - cost reference - bandwidth 64700 command i n router ospf mode
考题
What is the default metric used on IS -IS routers for each interface?（）A、The cost is set to 10 for all interfaces.B、The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C、The cost is based on the speed of the interface.D、The cost is based o n a composite of bandwidth and delay of the interface.
考题
In JUNOS software, what is the default interface metric for IS-IS?（）A、1B、10C、100D、10^8/link bandwidth
考题
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）A、1B、10C、1562D、64000E、128000
考题
This question is about the formation of OSPF adjacency. An OSPF adjacency will not form correctly across a point-to-point link in the same area. Which would most likely cause this problem？（）A、Each interface has a different OSPF cost.B、Each interface is configured with secondary addresses as well as primary addresses.C、Each interface has a different MTU size.D、Each interface is configured with theip unnumbered loopback 0 command.
考题
Network A has a spanning-tree problem in which the traffic is selecting a longer path. How is the path cost calculated？（）A、number of hopsB、priority of the bridgeC、interface bandwidthD、interface delayE、None of the above
考题
Which of the following commands would be applied to a WAN interface, but not on LAN Interface?（）A、IP addressB、encapsulation PPPC、no shutdownD、PPP authentication CHAPE、SpeedF、None of the above
考题
How is the cost of a virtual link in OSPF calculated?（）A、Takes the metric of the outgoing interface.B、Uses the metric that is assigned during configuration.C、Uses the path metric to reach the virtual link neighbor.D、Uses a default of zero unless otherwise specified.
考题
单选题What is the default metric used on IS -IS routers for each interface?（）A
The cost is set to 10 for all interfaces.B
The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C
The cost is based on the speed of the interface.D
The cost is based o n a composite of bandwidth and delay of the interface.
考题
单选题If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?（）A
1B
64C
1562D
64000E
1500
考题
单选题If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）A
1B
10C
1562D
64000E
128000F
None of the above
考题
单选题An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）A
1B
10C
1562D
64000E
128000
热门标签
最新试卷
