单选题A new Company switch was just configured using the "switchport trunk native vlan 7" command. What does this interface command accomplish？（）A Causes the interface to apply ISL framing for traffic on VLAN 7B Configures the trunking interface to forward traffic from VLAN 7C Configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q taggedD Configures the trunking interface to send traffic from VLAN 7 untaggedE None of the other alternatives apply

考题 A Ezonexam switch is configured with all ports assigned to VLAN 2. In addition, all ports are configured as full-duplex FastEthernet. What is the effect of adding switch ports to a new VLAN on this switch?A．The additions will create more collisions domains.B．IP address utilization will be more efficient.C．More bandwidth will be required than was needed previously.D．An additional broadcast domain will be created.E．The possibility that switching loops will occur will increase dramatically.

查看答案

考题 The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?（）A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.

查看答案

考题 A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch.Which of the following settings on the switch will need to be configured to support the printer?（）A. MAC filteringB. IP addressC. PoED. Port speed

查看答案

考题 A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero

查看答案

考题 Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? () A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.

查看答案

考题 A new Company switch was just configured using the "switchport trunk native vlan 7" command. What does this interface command accomplish？（）A、 Causes the interface to apply ISL framing for traffic on VLAN 7B、 Configures the trunking interface to forward traffic from VLAN 7C、 Configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q taggedD、 Configures the trunking interface to send traffic from VLAN 7 untaggedE、 None of the other alternatives apply

查看答案

考题 A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network. Which three issues on Switch2 could be the cause？（）A、Switch2 is configured for only VLAN1B、Switch2 is a VTP server in a different domainC、Switch2 is a VTP server in the Company domainD、Switch2 is not a VTP domain.E、Switch2 has a lower VTP configuration revision number than the current VTP revisionF、Switch2 has a higher VTP configuration revision number than the current VTP revision

查看答案

考题 You work as a network Technician. A new workstation has consistently been unable to obtain anIP address from the DHCP server when the workstation boots. Older workstations function normally， and the new workstation obtains an address when manually forced to renew its address. What should be configured on the switch to allow the workstation to obtain an IP address at boot？（）A、UplinkFast on the switch port connected to the serverB、BackboneFast on the switch port connected to the serverC、PortFast on the switch port connected to the workstationD、trunking on the switch

查看答案

考题 You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information？（）A、VTP modeB、VTP passwordC、VTP revision numberD、VTP pruningE、VTP domain nameF、None of the other alternatives apply

查看答案

考题 ISL is being configured on a Company switch. Which of the following choices are true regarding the ISL protocol？（）A、 It can be used between Cisco and non-Cisco switch devices.B、 It calculates a new CRC field on top of the existing CRC field.C、 It adds 4 bytes of protocol-specific information to the original Ethernet frame.D、 It adds 30 bytes of protocol-specific information to the original Ethernet frame.

查看答案

考题 Company.com network consists of a single Active Directory domain named Company.com.Company.com has an Exchange Server 2010 organization.The Company.com employees use Microsoft Office Outlook 2007 to connect to their mailboxes.RPC over HTTP and Auto discover are configured on Microsoft Office Outlook 2007. A new Company.com security policy requires that the employees connected to the domain does not need authentication when using Outlook Anywhere.However， those not connected t the domain needs to be authentication when using Outlook Anywhere.The employees need to comply with the new Company.com security policy. What should you do？（）A、You should consider using Basic authentication on Outlook Anywhere and set up only Basic authentication on the RPC virtual directory.B、You should consider using NTLM authentication on Outlook Anywhere and set up Basic authentication and NTLM authentication on the RPC virtual directory.C、You should consider using NTLM authentication on Outlook Anywhere and set up only Basic authentication on the RPC virtual directory.D、You should consider using Basic authentication on Outlook Anywhere and set up Basic authentication and NTLM authentication on the RPC virtual directory.

查看答案

考题 You have just created a new VLAN on your network. What is one step that you should include in your VLAN-based implementation and verification plan？（）A、Verify that trunked links are configured to allow the VLAN traffic.B、Verify that the switch is configured to allow for trunking on the switch ports.C、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.D、Verify that different native VLANs exist between two switches for security purposes.

查看答案

考题 You need to configure a new Company switch to support DTP. Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？（）A、 AccessB、 No negotiateC、 TrunkD、 Dynamic desirableE、 Dynamic autoF、 None of the other alternatives apply

查看答案

考题 A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?（）A、The switch that will share the VLAN information must be in the VTP Server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be configured to use the same VTP version.E、The switches must be configured to use the same STP version.F、The switches must be configured to use the same type of ID tagging.G、The switches must be connected over VLAN trunks.

查看答案

考题 Two Company switches are connected via a trunk using VTP. Which VTP information does a Catalyst switch advertise on its trunk ports when using VTP？（）A、STP root statusB、VTP modeC、Negotiation statusD、Management domainE、Configuration revision number

查看答案

考题 A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration?（）A、A switch in the VTP client mode cannot update its local VLAN database.B、A trunk link must be configured between the switches to forward VTP updates.C、A switch in the VTP server mode can update a switch in the VTP transparent mode.D、A switch in the VTP transparent mode will forward updates that it receives to other switches.E、A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.F、A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.

查看答案

考题 A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero

查看答案

考题单选题A new Company switch was just configured using the "switchport trunk native vlan 7" command. What does this interface command accomplish？（）A Causes the interface to apply ISL framing for traffic on VLAN 7B Configures the trunking interface to forward traffic from VLAN 7C Configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q taggedD Configures the trunking interface to send traffic from VLAN 7 untaggedE None of the other alternatives apply

查看答案

考题单选题A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）A oneB threeC twoD zero

查看答案

考题多选题ISL is being configured on a Company switch. Which of the following choices are true regarding the ISL protocol？（）AIt can be used between Cisco and non-Cisco switch devices.BIt calculates a new CRC field on top of the existing CRC field.CIt adds 4 bytes of protocol-specific information to the original Ethernet frame.DIt adds 30 bytes of protocol-specific information to the original Ethernet frame.

查看答案

考题单选题Which MST configuration statement is correct？（）A MST configurations can be propagated to other switches using VTP.B After MST is configured on a Switch， PVST+ operations will also be enabled by default.C MST configurations must be manually configured on each switch within the MST region.D MST configurations only need to be manually configured on the Root Bridge.E MST configurations are entered using the VLAN Database mode on Cisco Catalyst switches.

查看答案

考题单选题You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information？（）A VTP modeB VTP passwordC VTP revision numberD VTP pruningE VTP domain nameF None of the other alternatives apply

查看答案

考题单选题A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch. Which of the following settings on the switch will need to be configured to support the printer?（）A MAC filteringB IP addressC PoED Port speed

查看答案

考题多选题Two Company switches are connected via a trunk using VTP. Which VTP information does a Catalyst switch advertise on its trunk ports when using VTP？（）ASTP root statusBVTP modeCNegotiation statusDManagement domainEConfiguration revision number

查看答案

考题单选题You have just created a new VLAN on your network for inter-VLAN routing. What is one step that you should include in your VLAN-based implementation and verification plan？（）A Verify that different native VLANs exist between two switches for security purposes.B Verify that the switch is configured to allow for trunking on the switch ports.C Verify that each switch port has the proper IP address space assigned to it for the new VLAN. D Verify that the VLAN virtual interface has been correctly created and enabled.

查看答案

考题单选题You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？（）A Verify that different native VLANs exist between two switches for security purposes.B Verify that the VLAN was added on all switches with the use of the show vlan command. C Verify that the switch is configured to allow for trunking on the switch ports.D Verify that each switch port has the correct IP address space assigned to it for the new VLAN.

查看答案

考题单选题You work as the IT professional in an international company which is named Wiikigo. You are experiencedin implementing and administering a network operating system. You are specialized in deploying servers，configuring Windows Server 2008 Terminal services and network application services， and configuring aweb services infrastructure. You are in charge of a server that runs Windows Server 2008. The server hasthe Web Server （IIS） server role installed. The Web developer at your company creates a new Web sitethat runs an ASP.NET 3.0 Web application. The ASP.NET Web application must run under a securitycontext that is separate from any other ASP.NET application on the Web server. You create a local useraccount and grant account rights and permissions to run the ASP.NET Web application. Authentication forthe new Web site should be configured to support the Web application. What action should you perform？（）A The ASP.NET Impersonation setting should be configured to Enabled. Edit the ASP.NET Impersonation setting by specifying the new local user account.B The Windows Authentication setting should be configured to Enabled.C The Forms Authentication setting should be configured to Enabled by using all the default settings.D The ASP.NET State Service should be configured to log on to the new local user account by using the Services console.

查看答案

考题单选题You work as the enterprise exchange administrator at Company.com.The Company.com network consists of a single Active Directory domain named Company.com.Company.com has an Exchange Server 2010 organization.Due to circumstances， Company.com has acquired a new Internet domain name.This results in that the employees cannot receive e-mail that is sent to the new Internet domain name.The new Internet domain name is set up as an e-mail address suffix.The Company.com employees need to receive e-mail sent from the new Internet domain name. What should you do？（）A You should consider using an External Relay Accepted Domain.B You should consider using an Authoritative Accepted Domain.C You should consider using a remote domain.D You should consider using a new Receive connector.

查看答案

网友您好， 请在下方输入框内输入要搜索的题目：

网友您好，请在下方输入框内输入要搜索的题目：