网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
You need to configure a new Company switch to support DTP. Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？ （）
- A、 Access
- B、 No negotiate
- C、 Trunk
- D、 Dynamic desirable
- E、 Dynamic auto
- F、 None of the other alternatives apply
参考答案
更多 “ You need to configure a new Company switch to support DTP. Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？ （）A、 AccessB、 No negotiateC、 TrunkD、 Dynamic desirableE、 Dynamic autoF、 None of the other alternatives apply” 相关考题
考题
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)A. Switch(vlan) mode trunkB. Switch(config) switchport access mode trunkC. Switch(config-if) switchport mode trunkD. Switch(config-if) switchport trunk encapsulation dot1qE. Switch(config) switchport access mode 1F. Switch(vlan) trunk encapsulation dot1q
考题
在Cisco Catalyst 2950交换机上配置Trunk接口模式时,如果要禁止接口产生DTP帧,应该通过以下( )命令实现。
A、switchport mode accessB、switchport mode dynamic desirableC、switchport mode autoD、switchport nonegotiate
考题
在一台cisco catalyst 2950交换机上,要将端口F0／1设置为永久中继模式,需要使用( )配置命令。
A、Switch(config-if)#switchport mode accessB、Switch(config-if)#switchport dynamic autoC、Switch(config-if)#switchport mode trunkD、Switch(config-if)#switchport mode dynamic
考题
Which two of these are recommended practices with trunks? ()
A. use ISL encapsulationB. use 802.1q encapsulationC. set ISL to desirable and auto with encapsulation negotiate to support ILS protocol negotiationD. use VTP server mode to support dynamic propagation of VLAN information across the networkE. set DTP to desirable and desirable with encapsulation negotiate to support DTP protocol negotiation.
考题
Which set of commands is recommended to prevent the use of a hub in the access layer?()
A.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1B.switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1C.switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1D.switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
考题
Which commands, when used together, would create an 802.1Q link?（）A、Switch(vlan)# mode trunkB、Switch(config)# switchport access mode trunkC、Switch(config-if)# switchport mode trunkD、Switch(config-if)# switchport trunk encapsulation dot1qE、Switch(config)# switchport access mode 1F、Switch(vlan)# trunk encapsulation dot1q
考题
Which set of commands is recommended to prevent the use of a hub in the access layer?（）A、switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1B、switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1C、switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1D、switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
考题
You work as a network technician at Company. Your boss, Mrs. , is interested in switch spoofing. She asks you how an attacker would collect information with VLAN hoping through switch spoofing. You should tell her that the attacking station... （）A、...uses VTP to collect VLAN information that is sent out and then tags itself with the domain information in order to capture the data.B、...will generate frames with two 802.1Q headers to cause the switch to forward the frames to a VLAN that would be inaccessible to the attacker through legitimate means.C、...uses DTP to negotiate trunking with a switch port and captures all traffic that is allowed on the trunk.D、...tags itself with all usable VLANs to capture data that is passed through the switch， regardless of the VLAN to which the data belongs.E、None of the other alternatives apply
考题
You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A、 ip routingB、 switchport mode trunkC、 no switchportD、 switchport trunk native vlan 1E、 None of the other alternatives apply
考题
Which two of these are recommended practices with trunks？ （）A、 use ISL encapsulationB、 use 802.1q encapsulationC、 set ISL to desirable and auto with encapsulation negotiate to support ILS protocol negotiationD、 use VTP server mode to support dynamic propagation of VLAN information across the network E、 set DTP to desirable and desirable with encapsulation negotiate to support DTP protocol negotiation.
考题
Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）A、 The interface actively attempts to convert the link to a trunk link.B、 The interface is put into permanent trunking mode but prevented from generating DTP frames. C、 The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.D、 The interface is put into a passive mode， waiting to convert the link to a trunk link. E、 None of the other alternatives apply
考题
You are configuring an 802.1Q trunk between a Layer 2 switch and a firewall. You read in the documentation that the best way to set up a trunk is to set the port as dynamic desirable. The trunk is not coming up. Which one of these options would be a valid explanation？（）A、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode ONB、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode to OFFC、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode as autoD、The firewall does not support DTP.You should set the switchport trunk mode to ON
考题
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch， which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）A、 switchport access vlan vlan-idB、 switchportC、 switchport mode accessD、 no switchportE、 None of the other alternatives apply
考题
You are configuring an 802.1Q trunk between a Layer 2 switch and a firewall. You read in the documentation that the best way to set up a trunk is to set the port as dynamic desirable. The trunk is not coming up. Which one of these options would be a valid explanation？ （）A、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode ONB、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode to OFFC、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode asauto.D、The firewall does not support DTP. You should set the switchport trunk mode to ON
考题
You need to configure a new Cisco router to be installed in the VOIP network. Which threeinterface commands will configure the switch port to support a connected Cisco phone and to trustthe CoS values received on the port if CDP discovers that a Cisco phone is attached？（）A、switchport voice vlan vlan-idB、mls qos trust device cisco-phoneC、switchport priority extend cos_valueD、mls qos trust cosE、mls qos trust override cos
考题
Which command alone will disable trunking on a Layer 2 switch port？（）A、no switchport trunk native vlan vlan-idB、switchport nonegotiateC、no switchport mode dynamic desirableD、switchport mode access
考题
You need to configure a new Company switch for trunking. Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）A、 CompanySwitch（config-if）#switchport trunk encapsulation dot1qB、 CompanySwitch（config-if）#switchport trunk encapsulation itefC、 CompanySwitch（config-if）#switchport trunk encapsulation fddiD、 CompanySwitch（config-if）#switchport trunk encapsulation islE、 None of the other alternatives apply
考题
Which two of these are recommended practices with trunks？（）A、use ISL encapsulationB、use 802.1q encapsulationC、set ISL to desirable and auto with encapsulation negotiate to support ILS protocol negotiationD、use VTP server mode to support dynamic propagation of VLAN information across the networkE、set DTP to desirable and desirable with encapsulation negotiate to support DTP protocol negotiation
考题
The Company LAN switches are being configured to support the use of Dynamic VLANs. What should be considered when implementing a dynamic VLAN solution？（）A、Each switch port is assigned to a specific VLAN.B、Dynamic VLANs require a VLAN Membership Policy Server.C、Devices are in the same VLAN regardless of which port they attach to.D、Dynamic VLAN assignments are made through the command line interface.
考题
You need to configure a new Cisco router to be installed in the Company VOIP network. Which three interface commands will configure the switch port to support a connected Cisco phone and to trust the CoS values received on the port if CDP discovers that a Cisco phone is attached？ （）A、switchport voice vlan vlan-idB、mls qos trust device cisco-phoneC、switchport priority extend cos_valueD、mls qos trust cosE、mls qos trust override cos
考题
多选题Which two of these are recommended practices with trunks？（）Ause ISL encapsulationBuse 802.1q encapsulationCset ISL to desirable and auto with encapsulation negotiate to support ILS protocol negotiationDuse VTP server mode to support dynamic propagation of VLAN information across the networkEset DTP to desirable and desirable with encapsulation negotiate to support DTP protocol negotiation
考题
单选题Switch R1 has been configured with DTP using the desirable option. Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）A
The interface actively attempts to convert the link to a trunk link.B
The interface is put into permanent trunking mode but prevented from generating DTP frames. C
The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.D
The interface is put into a passive mode， waiting to convert the link to a trunk link. E
None of the other alternatives apply
考题
单选题You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch， which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）A
switchport access vlan vlan-idB
switchportC
switchport mode accessD
no switchportE
None of the other alternatives apply
考题
单选题You need to configure a new Company switch for trunking. Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）A
CompanySwitch（config-if）#switchport trunk encapsulation dot1qB
CompanySwitch（config-if）#switchport trunk encapsulation itefC
CompanySwitch（config-if）#switchport trunk encapsulation fddiD
CompanySwitch（config-if）#switchport trunk encapsulation islE
None of the other alternatives apply
考题
单选题Which command alone will disable trunking on a Layer 2 switch port？（）A
no switchport trunk native vlan vlan-idB
switchport nonegotiateC
no switchport mode dynamic desirableD
switchport mode access
考题
单选题You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A
ip routingB
switchport mode trunkC
no switchportD
switchport trunk native vlan 1E
None of the other alternatives apply
考题
单选题You need to configure a new Company switch to support DTP. Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？ （）A
AccessB
No negotiateC
TrunkD
Dynamic desirableE
Dynamic autoF
None of the other alternatives apply
热门标签
最新试卷
