网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
单选题
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）
A
There is a mismatch in encapsulation types
B
The wrong type of cable is connected to the interface
C
The interface has been configured with the shutdown command
D
The interface is not receiving any keepalives
E
The interface needs to be configured as a DTE device
F
There is no encapsulation type configured
参考答案
参考解析
解析：
暂无解析
更多 “单选题Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）A There is a mismatch in encapsulation typesB The wrong type of cable is connected to the interfaceC The interface has been configured with the shutdown commandD The interface is not receiving any keepalivesE The interface needs to be configured as a DTE deviceF There is no encapsulation type configured” 相关考题
考题
下列哪些命令可以用来查看DDR端口（在端口 S1 上配置）信息？（ ） A、 show interface B、 show running-conting C、 show interface s1 D、 show diater interface s1
考题
Which three route filtering statements are true?()
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
考题
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
考题
Refer to the exhibit.The actual speed of the serial links between R2 and R3 are 256 kb/s and 512k b/s respectively. When configuring EIGRP on routers R2 and R3, the network administrator configured the bandwidth of both serial interfaces to 512 kb/s. What will be the effect?（）A. EIGRP will overutilize the 512 kb/s link.B. The interface delay value used in the EIGRP metric calculation will be inaccurate on the 256k b/s serial interface.C. The amount of bandwidth used for EIGRP routing protocol traffic on the 256 kb/s link can become excessive.D. EIGRP can load balance between the two serial links only if the variance is set to 2 or higher.E. Unequal cost load balancing will be disabled.
考题
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? ()
A.S1(config)# interface fastethernet 0/1S1(config - if)# ip helper - address 10.0.0.2B.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1C.R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1D.R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1E.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
考题
What is the reason for configuring a passive interface on a router?()
A. Allows interfaces to share common IP addresses.B. Allows an interface to remain up without the aid of keepalives.C. Allows a router to send routing and not receive updates via that interface.D. Allows a routing protocol to forward updates that is missing its IP address.E. Allows a router to receive routing updates on an interface but not send updates via that interface.
考题
Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?（）A.Telnet to WANRouter and execute the command show interfaces S0/0B.Telnet to WANRouter and execute the commandshow processes S0/0C.Telnet to WANRouter and execute the command show running-configurationD.Telnet to WANRouter and execute the command show controller S0/0E.Physically examine the cable between WANRouter S0/0 and the DCE.F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0
考题
Refer to the exhibit.What is the meaning of the term dynamic as displayed in the output of the show frame－relay map command shown?()
A.The Seria l0/0interface is passing traffic.B.The DLCI 100 was dynamic allyallocated by the routerC.The Seria l0/0 interf aceacquired the IP address of 172.16.3.1 from a DHCP serverD.The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloudE.The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
考题
Refer to the exhibit.If the devices produced the given output,what is the cause of the EtherChannel problem?()
A.There is a speed mismatch between SW1‘s Fa0/1 and SW2‘s Fa0/1 interfaces.B.There is an MTU mismatch between SW1‘s Fa0/1 and SW2‘s Fa0/1 interfaces.C.There is an encapsulation mismatch between SW1‘s Fa0/1 and SW2‘s Fa0/1 interface.D.SW1‘s Fa0/1 interface is administratively shut down.
考题
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?()
A.There is a mismatch in encapsulation typesB.The wrong type of cable is connected to the interfaceC.The interface has been configured with the shutdown commandD.The interface is not receiving any keepalivesE.The interface needs to be configured as a DTE deviceF.There is no encapsulation type configured
考题
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0／10 is not the root port for VLAN 2?()
A.This switch has more than one interface connected to the root network segment in VLAN 2.B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.C.This switch interface has a higher path cost to the root bridge than another in the topology.D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.
考题
Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN?()
A.The number of collision domains would decrease.B.The number of collision domains would increase.C.The number of broadcast domains would remain the same.D.The number of collision domains would remain the same.E. The number of broadcast domains would increase.
考题
Refer to the graphic.Host A is communicating with the seiver. What will be the source MAC address of the frames received by Host A from the server?()
A.the MAC address of the seiver network interfaceB.the MAC address of host AC.the MAC address of router interface e 1D.the MAC address of router interface e0
考题
Refer to the exhibit, Host A pings interface S0／0 on router 3, what is the TTL value for that ping?()
A. 253B. 252C. 255D. 254
考题
Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）A、HostA is not on the same subnet as its default gatewayB、The address of SwitchA is a subnet addressC、The Fa0/0 interface on RouterA is on a subnet that cannot be usedD、The serial interfaces of the routers are not on the same subnetE、The Fa0/0 interface on RouterB is using a broadcast address
考题
Refer to the exhibit. Which two statements are true about the partial configuration that is shown？（）A、Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the routerB、The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address10.10.0.1C、The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.1D、DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2E、The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.6
考题
A network administrator receives an error message while tring to configure the Ethernet interface of arouter with IP address 10.24.24.24/29.which statement explains the reason for this issue？（）A、The address is a broadcast addressB、The Ehernet interface is faultyC、VLSM-capable routing protocols must be enable first on the router.D、This address is a network address.
考题
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）A、There is a mismatch in encapsulation typesB、The wrong type of cable is connected to the interfaceC、The interface has been configured with the shutdown commandD、The interface is not receiving any keepalivesE、The interface needs to be configured as a DTE deviceF、There is no encapsulation type configured
考题
What is the reason for configuring a passive interface on a router?（）A、Allows interfaces to share common IP addresses.B、Allows an interface to remain up without the aid of keepalives.C、Allows a router to send routing and not receive updates via that interface.D、Allows a routing protocol to forward updates that is missing its IP address.E、Allows a router to receive routing updates on an interface but not send updates via that interface.
考题
Which three route filtering statements are true?（）A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
考题
Refer to the exhibit.What is the effect of the configuration that is shown?（）A、It tells the router or switch to try establish an SSH connection first and if that fail to use telnet.B、It configures a cisco network device to use the SSH protocol on incoming communications via the virtual terminal ports.C、It allows seven failed login attempts before the VTY lines are temporarily shutdown.D、It configures the virtual terminal lines with the password 030752180500.E、It configures SSH globally for all logins.
考题
单选题What does the underlined word “it” in Paragraph 3 refer to?A
Nathan’s work.B
Nathan’s exhibition.C
Nathan’s art.D
Nathan’s self-portrait.
考题
单选题Refer to the exhibit. The command spanning-tree guard root is configured on interface Gi0/0 on both switch S2 and S5. The global configuration command spanning-tree uplinkfast has been configured on both switch S2 and S5. The link between switch S4 and S5 fails. Will Host A be able to reach Host B？（）A
Yes. Traffic can pass either from switch S6 to S3 to S2 to S1， or， from switch S6 to S5 to S2 to S1.B
No. Traffic will pass from switch S6 to S5 and dead-end at interface Gi 0/0.C
No. Traffic will loop back and forth between switch S5 and S2.D
Yes. Traffic will pass from switch S6 to S3 to S2 to S1.E
No. Traffic will either pass from switch S6 to S5 and dead-end， or traffic will pass from switch S6 to S3 to S2 and dead-end.
考题
多选题Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN?（）AThe number of collision domains would decrease.BThe number of collision domains would increase.CThe number of broadcast domains would remain the same.DThe number of collision domains would remain the same.EThe number of broadcast domains would increase.
考题
单选题Which statement about a none zero value for the load metric (k2) for EIGRP is true?（）A
A change in the load on an interface will cause EIGRP to recalculate the routing metrics and send a corresponding update out to each of its neighbors.B
EIGRP calculates interface load as a 5 - minute exponentially weighted average that is updated every 5 minutes.C
EIGRP considers the load of an interface only when sending an update for some other reason.D
A change in the load on an interface will cause EIGRP to recalculate and update the administrative distance for all routes learne d on that interface.
考题
多选题Refer to the exhibit. Which two statements are true about the partial configuration that is shown？（）AHosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the routerBThe first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address10.10.0.1CThe first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.1DDHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2EThe first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.6
热门标签
最新试卷
