网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
While logged into a router, you wish to see the RIP routing updates in real time as they are sent and received. Which command would you issue to see these updates?()
A. Show ip protocols
B. Show ip route rip
C. Debug ip rip
D. Debug ip updates
E. Debug ip transactions
参考答案
更多 “ While logged into a router, you wish to see the RIP routing updates in real time as they are sent and received. Which command would you issue to see these updates?() A. Show ip protocolsB. Show ip route ripC. Debug ip ripD. Debug ip updatesE. Debug ip transactions ” 相关考题
考题
Which three route filtering statements are true?()
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
考题
While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?（）A. pingB. traceC. show ip routeD. show interfaceE. show cdp neighbors
考题
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）A. TK1# show versionB. TK1# show protocolsC. TK1# show interfacesD. TK1# show controllersE. TK1# show ip interfaceF. TK1# show startup-config
考题
After executing the "show host" command, which of the information below would you see?()
A. The IP addresses of workstations allowed gain access to the router via an access listB. Permanent name-to-address mappings created using the ip host command.C. Temporary and permanent DNS entries.D. The names of the routers created using the hostname command.E. The length of time of users logged into the router, as well as the duration
考题
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? ()
A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
考题
Which of the commands below would you enter if you wanted to see the configuration register of your router?()
A. show bootB. show flashC. show registerD. show versionE. show config
考题
You need to choose a routing protocol for a new Testking network. This network will be running IP, IPX, and Appletalk, and you wish to utilize only one routing protocol. Which one would be the best choice?（）A. OSPFB. EIGRPC. RIP v2D. IGRPE. RIP v1
考题
Which two statements are characteristics of a distance vector routing protocol?（）A、RIP is an example of distance vector routing protocolsB、Updates are periodic and include the entire routing tableC、Routing updates are sent only after topology changesD、The protocol can be useful in hub-and-spoke and hierarchical networksE、Convergence is usually faster than with link state protocolsF、Each router has its own view of the topology
考题
The Testking router is running both RIP and IGRP, and the same route is learned by this router from both of these methods. However, when you issue the command"show ip route" you see only the IGRP route, and not the RIP route. Why is this?（）A、IGRP has a faster update timer.B、IGRP has a lower administrative distance.C、RIP has a higher metric value for that route.D、The IGRP route has fewer hops.E、The RIP path has a routing loop.
考题
Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive - interface router configuration command is entered?（）A、EIGRPB、RIPC、OSPFD、IS - IS
考题
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state. What must be true in an SVI configuration to bring the VLAN and line protocol up？（）A、The port must be physically connected to another Layer 3 device.B、At least one port in VLAN 20 must be active.C、The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.D、Because this is a virtual interface， the operational status will always be in an "up/up" state.
考题
You need to choose a routing protocol for a new Testking network. This network will be running IP, IPX, and Appletalk, and you wish to utilize only one routing protocol. Which one would be the best choice?（）A、OSPFB、EIGRPC、RIP v2D、IGRPE、RIP v1
考题
At which command prompt would you issue the set date command?（）A、[edit chassis]user@router#B、[edit]user@router#C、[edit system] user@router#D、user@router
考题
Which of the commands below would you enter if you wanted to see the configuration register of your router?（）A、show bootB、show flashC、show registerD、show versionE、show config
考题
Which two statements are characteristics of a distance vector routing protocol?（）A、RIP is an example of distance vector routing protocols.B、Updates are periodic and include the entire routing table.C、Routing updates are sent only after topology changesD、The protocol can be useful in hub-and-spoke and hierarchical networks.E、Convergence is usually faster than with link state protocolsF、Each router has its own view of the topology
考题
While logged into a router, you wish to see the RIP routing updates in real time as they are sent and received. Which command would you issue to see these updates?（）A、Show ip protocolsB、Show ip route ripC、Debug ip ripD、Debug ip updatesE、Debug ip transactions
考题
Which three route filtering statements are true?（）A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
考题
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface. Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）A、TK1# show versionB、TK1# show protocolsC、TK1# show interfacesD、TK1# show controllersE、TK1# show ip interfaceF、TK1# show startup-config
考题
While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?（）A、pingB、traceC、show ip routeD、show interfaceE、show cdp neighbors
考题
After executing the "show host" command, which of the information below would you see?（）A、The IP addresses of workstations allowed gain access to the router via an access listB、Permanent name-to-address mappings created using the ip host command.C、Temporary and permanent DNS entries.D、The names of the routers created using the hostname command.E、The length of time of users logged into the router, as well as the duration
考题
单选题While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?（）A
pingB
traceC
show ip routeD
show interfaceE
show cdp neighbors
考题
单选题While logged into a router, you wish to see the RIP routing updates in real time as they are sent and received. Which command would you issue to see these updates?（）A
Show ip protocolsB
Show ip route ripC
Debug ip ripD
Debug ip updatesE
Debug ip transactions
考题
单选题In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）A
The IP addresses are configured incorrectly.B
Frame Relay LMI messages not displayed in real time.C
The administrator must issue the enable frame-relay lmi debug command.D
The administrator must issue the terminal monitor command.E
Debug messages can only be received once through the console port.F
The administrator must issue the show frame-relay lmi vty 0 4 command
考题
单选题The Testking router is running both RIP and IGRP, and the same route is learned by this router from both of these methods. However, when you issue the command"show ip route" you see only the IGRP route, and not the RIP route. Why is this?（）A
IGRP has a faster update timer.B
IGRP has a lower administrative distance.C
RIP has a higher metric value for that route.D
The IGRP route has fewer hops.E
The RIP path has a routing loop.
考题
单选题Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive - interface router configuration command is entered?（）A
EIGRPB
RIPC
OSPFD
IS - IS
考题
单选题Which of the commands below would you enter if you wanted to see the configuration register of your router?（）A
show bootB
show flashC
show registerD
show versionE
show config
考题
单选题At which command prompt would you issue the set date command?（）A
[edit chassis]user@router#B
[edit]user@router#C
[edit system] user@router#D
user@router
热门标签
最新试卷
