网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
- A、The bypass-routing parameter is used to test the density on the T1 line.
- B、The bypass-routing parameter cannot be used on a T1 interface.
- C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
- D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.
参考答案
更多 “You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the T1 line.B、The bypass-routing parameter cannot be used on a T1 interface.C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.” 相关考题
考题
When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?()
A.ping atm vci 0.100 interface at-0/1/0 end-to-endB.ping atm vci 0.100 interface at-0/1/0 circuitC.ping atm vci 0.100 interface at-0/1/0 far-endD.ping atm vci 0.100 interface at-0/1/0 final-hop
考题
Asystemadministratoristryingtotroubleshootcompanywideemailproblemsthatmayberelated toDNS.WhichofthefollowingnetworktoolswouldbeMOSTusefultodetermineifitisaDNS issue?()
A.netstatB.tracertC.nslookupD.ping
考题
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()
A. Issue the command bandwidth 224 on the physical interface.B. Issue the command bandwidth 56 on the physical interface.C. Issue the command bandwidth 224 on each subinterface.D. Issue the command bandwidth 56 on each subinterface.
考题
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
考题
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）A. Serial 0 is up, line protocol is upB. Serial 0 is up, line protocol is downC. Serial 0 is down, line protocol is downD. Serial 0 is down, line protocol is upE. Serial 0 is administratively down, line protocol is downF. Serial 0 is administratively down, line protocol is up
考题
You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()
A. Show interface lmiB. Show frame-relay lmiC. Show interface frame-relayD. Debug frame-relay interface.
考题
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()
A.show ip access-listB.show access-listC.list ip interfaceD.show interfaceE.show ip interface
考题
While troubleshooting a connectivity issue from a PC you obtain the following information: Local PC IP address: 10.0.0.35/24 Default Gateway: 10.0.0.1 Remote Sever: 10.5.75.250/24 You then conduct the following tests from the local PC: Ping 127.0.0.1 – Successful Ping 10.0.0.35 – Successful Ping 10.0.0.1 – Unsuccessful Ping 10.5.75.250 – Unsuccessful What is the underlying cause of this problem?（）A、A remote physical layer problem exists.B、The host NIC is not functioning.C、TCP/IP has not been correctly installed on the host.D、A local physical layer problem exists.
考题
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）A、Serial 0 is up, line protocol is upB、Serial 0 is up, line protocol is downC、Serial 0 is down, line protocol is downD、Serial 0 is down, line protocol is upE、Serial 0 is administratively down, line protocol is downF、Serial 0 is administratively down, line protocol is up
考题
You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall commandB、The count parameter allows the router to count the number of pings for logging purposesC、The count parameter allows the router to pause for 10000 seconds before sending out a pingD、The count parameter allows the router to send out 1000 pings and then stop
考题
You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall command.B、The count parameter allows the router to count the number of pings for logging purposes.C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.D、The count parameter allows the router to send out 1000 pings and then stop.
考题
YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the TI line.B、The bypass-routing parameter cannot be used on a T1 interface.C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
考题
When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?（）A、ping atm vci 0.100 interface at-0/1/0 end-to-endB、ping atm vci 0.100 interface at-0/1/0 circuitC、ping atm vci 0.100 interface at-0/1/0 far-endD、ping atm vci 0.100 interface at-0/1/0 final-hop
考题
You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the T1 lineB、The bypass-routing parameter cannot be used on a T1 interfaceC、The bypass-routing parameter allows you to ping a host through an interface that has no route through itD、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
考题
While troubleshooting a connectivity problem on the network, you issue the ping command from your PC command prompt, but the output shows "request times out."At which OSI layer is this problem associated with?（）A、The data link layerB、The application layerC、The access layerD、The session layerE、The network layer
考题
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface. Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）A、TK1# show versionB、TK1# show protocolsC、TK1# show interfacesD、TK1# show controllersE、TK1# show ip interfaceF、TK1# show startup-config
考题
When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）A、show ip access-listB、show access-listC、list ip interfaceD、show interfaceE、show ip interface
考题
You want to allow all hosts on interface ge-0/0/0.0 to be able to ping the device’s ge-0/0/0.0 IP address.Where do you configure this functionality？（）A、[edit interfaces]B、[edit security zones]C、[edit system services]D、[edit security interfaces]
考题
单选题While troubleshooting a connectivity issue from a PC you obtain the following information: Local PC IP address: 10.0.0.35/24 Default Gateway: 10.0.0.1 Remote Sever: 10.5.75.250/24 You then conduct the following tests from the local PC: Ping 127.0.0.1 – Successful Ping 10.0.0.35 – Successful Ping 10.0.0.1 – Unsuccessful Ping 10.5.75.250 – Unsuccessful What is the underlying cause of this problem?（）A
A remote physical layer problem exists.B
The host NIC is not functioning.C
TCP/IP has not been correctly installed on the host.D
A local physical layer problem exists.
考题
单选题You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A
The bypass-routing parameter is used to test the density on the T1 lineB
The bypass-routing parameter cannot be used on a T1 interfaceC
The bypass-routing parameter allows you to ping a host through an interface that has no route through itD
The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
考题
单选题While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）A
Serial 0 is up, line protocol is upB
Serial 0 is up, line protocol is downC
Serial 0 is down, line protocol is downD
Serial 0 is down, line protocol is upE
Serial 0 is administratively down, line protocol is downF
Serial 0 is administratively down, line protocol is up
考题
单选题You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A
The bypass-routing parameter is used to test the density on the T1 line.B
The bypass-routing parameter cannot be used on a T1 interface.C
The bypass-routing parameter allows you to ping a host through an interface that has no route through it.D
The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.
考题
单选题You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）A
The count parameter creates a counter that you can view with the show firewall command.B
The count parameter allows the router to count the number of pings for logging purposes.C
The count parameter allows the router to pause for 1000 seconds before sending out a ping.D
The count parameter allows the router to send out 1000 pings and then stop.
考题
单选题YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A
The bypass-routing parameter is used to test the density on the TI line.B
The bypass-routing parameter cannot be used on a T1 interface.C
The bypass-routing parameter allows you to ping a host through an interface that has no route through it.D
The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
考题
单选题When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）A
show ip access-listB
show access-listC
list ip interfaceD
show interfaceE
show ip interface
考题
单选题You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?（）A
Show interface lmiB
Show frame-relay lmiC
Show interface frame-relayD
Debug frame-relay interface.
考题
单选题You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A
The count parameter creates a counter that you can view with the show firewall commandB
The count parameter allows the router to count the number of pings for logging purposesC
The count parameter allows the router to pause for 10000 seconds before sending out a pingD
The count parameter allows the router to send out 1000 pings and then stop
热门标签
最新试卷
