网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）
- A、R1 will always create and flood a default route into the OSPF domain.
- B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.
- C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.
- D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
参考答案
更多 “ Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）A、R1 will always create and flood a default route into the OSPF domain.B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.” 相关考题
考题
以下是路由器R1的部分配置，请完成其配置，或解释配置命令含义。!R1 (Config) interface fastethernet0R1(Config-if) ip address (6) (7)R1(Config-if) (8) (开启端口)!R1 (Config) interface serial 0R1(Config-if) ip address (9) (10)!R1 (Config) ip routingR1 (Config) router rip (11)R1 (Config-router) (12) (声明网络)R1 (Config-router) (13) (声明网络)R1 (Config-router) (14) (声明网络)R1 (Config-router) version 2 (15)!
考题
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
考题
The following output exists on Router R1, a router internal to area 1. What can you d etermine as true from the output of the show ip ospf database summary command?()
A. The LSA was created by an ABR due to an area range command.B. The LSA was created by an ASBR due to a summary - address command.C. If cr eated by an area range command, the best metric for a subordinate subnet on that ABR must have been 11.D. None of the other answers is correct.
考题
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
考题
Based on the show ip route isis output on R1, which statement is true? ()
A. The i su 10.1.0.0/23 route is a suppressed route.B. The i su 10.1. 0.0/23 route is a summary route.C. The i su 10.1.0.0/23 route is an IS - IS external route.D. The R1 IS - IS router is an ASBR.E. The R1 IS - IS router is an ABR that belongs to multiple IS - IS areas.F. The R1 IS - IS router is performing route aggregation and is suppressing the more specific 10.1.0.0/23 prefix.
考题
Refer to the exhibit. Router C was configured so that it could form an adja cency with three OSPF neighbors, one connected to each of its three physical interfaces. Which statement is correct about router C?（）A. It is configured and functioning correctly as an OSPF internal router.B. It is configured and functioning correc tly as an ABR attached to stub area 4.C. It is configured and functioning correctly as an ASBR attached to external area 4.D. It is configured and functioning correctly as an ABR attached to totally stubby area 4.E. It is not configured correctly to function as specified.
考题
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 ／26 and 172.16.1.64 ／27. On the basis of the partial output in the exhibit, which statement is true? ()
A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.B. Router R1 will advertise both rou tes.C. Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
考题
Whichseriesofcommands willconfigurerouterR1forLAN－to－LANcommunicationwithrouterR2?Theenterprisenetworkaddressis192.1.1.0／24andtheroutingprotocolinuseisRIP.()
A.R1（config）#interfaceethernet0；R1（config-if）#ipaddress192.1.1.129255.255.255.192；R1（config-if）#noshutdownB.R1（config）#interfaceethernet0；R1（config-if）#ipaddress192.1.1.97255.255.255.192；R1（config-if）#noshutdownC.R1（config）#interfaceserial0；R1（config-if）#ipaddress192.1.1.4255.255.255.252；R1（config-if）#clockrate56000D.R1（config）#interfaceserial0；R1（config-if）#ipaddress192.1.1.6255.255.255.252；R1（config-if）#noshutdownE.R1（config）#routerrip；R1（config-router）#network192.1.1.4；R1（config-router）#network192.1.1.128F.R1（config）#routerrip；R1（config-router）#version2；R1（config-router）#network192.1.1.0
考题
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? ()
A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.
考题
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
考题
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
考题
Examine the following excerpt from the show ip ospf database asbr -summary command on router R1 (RID 1.1.1.1). Which answer can be verified as definitely true based on this output?（） LS Type: Summary Links (AS Boundary Router) Link State ID: 9.9.9.9 (AS Boundary Router address) Advertising Router: 3.3.3.3 LS Seq Number: 8000000D Checksum: 0xE43A Length: 28 Network Mask: /0 TOS: 0 Metric: 100A、The output describes the contents of a Type 5 LSAB、3.3.3.3 identifies a ro uter as being the router performing redistributionC、R1's metric for its best route to reach the router with RID 9.9.9.9 is 100D、The router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
考题
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782.The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?（）A、Router R2 will not form a neighbor relationship with R1.B、Router R2 will obtain a full routing table, including a default route, from R1.C、R2 will obtain OSPF updates from R1, but will not obtain a default route from R1.D、R2 will not have a route for the directly connected serial network, but all other directly connected
考题
Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）A、 InitB、 IdleC、 ActiveD、 StandbyE、 EstablishedF、 Backup
考题
Which of the following LSA is the Type 10？（）A、Router LSAB、Opaque LSAC、AS attributes LSAD、ASBR summary LSAE、Network summary LSA
考题
Which LSA is the Type 10？（）A、Router LSAB、Opaque LSAC、AS attributes LSAD、ASBR summary LSAE、Network summary LSA
考题
如果在ASBR上，引入到OSPF的外部路由的下一跳在此OSPF路由域内，则相关AS-External-LSA的Forwarding Address应当被设置为（）。A、0.0.0.0B、此ASBR的RouterIDC、此ASBR所在区域的ABR的Router IDD、ASBR上此外部路由实际的下一跳
考题
如果在ASBR上，引入到OSPF的外部路由的下一跳不在此OSPF路由域内，则相关AS-External-LSA的Forwarding Address应当被设置为（）。A、0.0.0.0B、此ASBR的Router IDC、此ASBR所在区域的ABR的Router IDD、ASBR上此外部路由实际的下一跳
考题
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
考题
A problem was reported that the 10.10.10.0/24 prefix was not injected into the local BGP table ona Company router named R1. The following information is available from this router： R1 Configuration： router bgp 65001 network 10.0.0.0 neighbor 172.16.1.1 remote-as 65002 no auto-summary Routing table information： show ip route | include 10 O 10.10.10.0/24 [110/11] via 192.168.1.1， 2d00h， Ethernet0/0 Why is this prefix not in the local BGP table of the R1？（）A、The 172.16.1.1 neighbor is down.B、The prefix 10.10.10.0/24 is not a ’connected’ routeC、This route is not a BGP learned routeD、The network command is wrongE、None of the other alternatives apply
考题
单选题Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）A
R1 will always create and flood a default route into the OSPF domain.B
R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.C
R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.D
R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
考题
单选题Examine the following excerpt from the show ip ospf database asbr -summary command on router R1 (RID 1.1.1.1). Which answer can be verified as definitely true based on this output?（） LS Type: Summary Links (AS Boundary Router) Link State ID: 9.9.9.9 (AS Boundary Router address) Advertising Router: 3.3.3.3 LS Seq Number: 8000000D Checksum: 0xE43A Length: 28 Network Mask: /0 TOS: 0 Metric: 100A
The output describes the contents of a Type 5 LSAB
3.3.3.3 identifies a ro uter as being the router performing redistributionC
R1's metric for its best route to reach the router with RID 9.9.9.9 is 100D
The router with RID 3.3.3.3's metric for its best route to reach the router with RID 9.9.9.9 is 100
考题
单选题A problem was reported that the 10.10.10.0/24 prefix was not injected into the local BGP table ona Company router named R1. The following information is available from this router： R1 Configuration： router bgp 65001 network 10.0.0.0 neighbor 172.16.1.1 remote-as 65002 no auto-summary Routing table information： show ip route | include 10 O 10.10.10.0/24 [110/11] via 192.168.1.1， 2d00h， Ethernet0/0 Why is this prefix not in the local BGP table of the R1？（）A
The 172.16.1.1 neighbor is down.B
The prefix 10.10.10.0/24 is not a ’connected’ routeC
This route is not a BGP learned routeD
The network command is wrongE
None of the other alternatives apply
考题
单选题Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）A
R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B
For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C
For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D
No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
考题
多选题Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？ （）AInitBIdleCActiveDStandbyEEstablishedFBackup
热门标签
最新试卷
