网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
Which two field-replaceable units FRUs are hot-swappable？（）
- A、Routing Engine on M10i
- B、Physical Interface Card on M7i
- C、fan tray on J-series routers
- D、Physical Interface Modules on J6300 router
参考答案
更多 “Which two field-replaceable units FRUs are hot-swappable？（）A、Routing Engine on M10iB、Physical Interface Card on M7iC、fan tray on J-series routersD、Physical Interface Modules on J6300 router” 相关考题
考题
To troubleshoot interface problems, you can use both the disable command and the deactivate command. Which two statements are correct?()
A.If the interface is disabled, the logical unit will administratively shutdown.B.If the interface is deactivated, the physical interface will administratively shutdown.C.If the interface is deactivated, the interface configuration is ignored during commit.D.If the interface is disabled, the logical unit configuration is ignored during commit.
考题
Which two statements are true regarding interface properties? ()
A.MTU and speed must be configured under each unit.B.Physical parameters such as MTU, duplex mode, and speed are configured under the interface name.C.IP and IPv6 addresses are configured under a unit-number.D.DLCI numbers, VPI/VCI values, and VLAN tags are physical parameters.
考题
Which of the following is true concerning Frame Relay multipoint subinterfaces?()
A. An IP address is required on the physical interface of the central router.B. All routers are required to be fully meshed.C. All routers must be in the same subnet to forward routing updates and broadcasts.D. Multipoint is the default configuration for Frame Relay subinterfaces.
考题
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit.Which of the following processes are required to accomplish this task?()
A. configure static frame relay map entries for each subinterface network.B. remove the ip address from the physical interfaceC. create the virtual interfaces with the interface commandD. configure each subinterface with its own IP addressE. disable split horizon to prevent routing loops between the subinterface networksF. encapsulate the physical interface with multipoint PPP
考题
Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.()
A.Router John uses alink-state routing protocol.B.Router John will receive routing updates on the Serial0/0 interface.C.Router John will receive routing updates on the Serial0/1 interface.D.Router John will send routing updates out the Serial0/0 interface.E.Router John will send routing updates out the FastEthernet0/0 interface.F.Router John will send routing updates out the Serial0/1 interface.
考题
On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）A.a router with subinterfaces configured on the physical interface that is connected to the switchB.a router with an IP address on the physical interface connected to the switchC.a switch with an access link that is configured between the switchesD.a switch with a trunk link that is configured between the switches
考题
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs()。
A.a switch with a trunk link that is configured between the switchesB.a router with an IP address on the physical interface that is connected to the switchC.a switch with an access link that is configured between the switchesD.a router with subinterfaces configured on the physical interface that is connected to the switch
考题
Use the output from the router shown in the graphic above to determine which of the following are correct.()
A. Router John uses a link-state routing protocol.B. Router John will receive routing updates on the Serial0/0 interface.C. Router John will receive routing updates on the Serial0/1 interface.D. Router John will send routing updates out the Serial0/0 interface.E. Router John will send routing updates out the FastEthernet0/0 interface.F. Router John will send routing updates out the Serial0/1 interface.
考题
Which statement is true regarding the Port Aggregation Protocol？ （）A、Configuration changes made on the port-channel interface apply to all physical ports assigned to the portchannel interface.B、Configuration changes made on a physical port that is a member of a port-channel interface apply to the port-channel interface.C、Configuration changes are not permitted with Port Aggregation Protocol； instead， the standardized Link Aggregation Control Protocol should be used if configuration changes are required.D、The physical port must first be disassociated from the port-channel interface before any configuration changes can be made.
考题
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch
考题
When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）A、The local DLCI on each subinterface of the Frame Relay.B、The Frame Relay encapsulation on the physical interface.C、An IP address on the physical interface.D、The subinterface type as point-to-point
考题
Which two statements are true regarding interface properties? （）A、MTU and speed must be configured under each unit.B、Physical parameters such as MTU, duplex mode, and speed are configured under the interface name.C、IP and IPv6 addresses are configured under a unit-number.D、DLCI numbers, VPI/VCI values, and VLAN tags are physical parameters.
考题
Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）A、Configure a routing process using the command ipv6 router ospf [process-id].B、Add the network statement for the interfaces on which OSPF will run.C、Configure OSPF on the interface that it will run on.D、Use the passive-interface command on the interfaces on which OSPF should not run.E、Enable routing.
考题
Overlay Transport Virtualization （OTV） join interface is used to source the OTV encapsulated traffic and send it to the Layer 3 domain of the data center network. Which statements are true about OTV join interface？ （）A、 Join interface is a Layer 3 entity， and with the Cisco NX-OS release 6.0， it can only be defined as a physical interface， physical subinterface， Layer 3 port channel， or Layer 3 port channel subinterface.B、 A single join interface can be defined and associated with a given OTV overlay.C、 Multiple overlays can also share the same join interface.D、 Join interface can be a loopback interface.E、 The join interface is a Layer 3 entity that can be defined as a physical interface but not as a logical one.
考题
Which three elements must be used when you configure a router interface for vlan trunking?（）A、one IP network or subnetwork for each subinterfaceB、subinterface numbering that matches vlan tagesC、subinterface encapsulation identifiers that match vlan tagsD、a management domain for each subinterfaceE、one physical interface for each subinterfaceF、one subinterface per vlan
考题
Which two statements are true about the role of split horizon？（）A、It is a function used by routing protocols to install routes into routing tableB、It is a function that prevents the advertising of routes over an interface that the router is usingto reach a routeC、Its function is to help avoid routing loops.D、It is a redistribution technique used by routing protocols
考题
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtualcircuit.Which of the following processes are required to accomplish this task？（）A、configure static frame relay map entries for each subinterface network.B、remove the ip address from the physical interfaceC、create the virtual interfaces with the interface commandD、configure each subinterface with its own IP addressE、disable split horizon to prevent routing loops between the subinterface networksF、encapsulate the physical interface with multipoint PPP
考题
Which three causes could prevent a host from getting an IPv6 address with stateless autoconfiguration？（）A、The autoconfig command is missing from the router interface.B、IPv6 multicast routing is not enabled on the router interface.C、IPv6 unicast routing is not enabled on the router interface.D、The router interface is configured with a /63 mask.E、The router interface is configured with a /65 mask.
考题
Which statements are valid for a local SPAN configuration？ （）A、 Source and destination interface must be on the same hostB、 Source and destination interfaces can be on different hostsC、 Destination vEthernet interface can be on a different VLAN than the sourceD、 Destination interface can be a physical portE、 Destination interface cannot be a physical port
考题
On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）A、a router with subinterfaces configured on the physical interface that is connected to the switchB、a router with an IP address on the physical interface connected to the switchC、a switch with an access link that is configured between the switchesD、a switch with a trunk link that is configured between the switches
考题
Which two statements are correct regarding units in JUNOS?（）A、Units in JUNOS are always required for any interface configured with logical addresses such as IP and IPv6.B、Units in JUNOS are only required when you are configuring sub-interfaces for inter-VLAN routing.C、Unit numbers must match the DLCI or VCI numbers configured on the interface.D、Unit 0 is the only value allowed on interfaces running HDLC, PPP, or for Ethernet interfaces not doing VLAN-tagging.
考题
Which two statements are true about hierarchical architecture? （）(Choose two.)A、You can assign a logical interface to multiple zones.B、You cannot assign a logical interface to multiple zones.C、You can assign a logical interface to multiple routing instances.D、You cannot assign a logical interface to multiple routing instances.
考题
多选题To troubleshoot interface problems, you can use both the disable command and the deactivate command. Which two statements are correct?（）AIf the interface is disabled, the logical unit will administratively shutdown.BIf the interface is deactivated, the physical interface will administratively shutdown.CIf the interface is deactivated, the interface configuration is ignored during commit.DIf the interface is disabled, the logical unit configuration is ignored during commit.
考题
多选题Which statements are valid for a local SPAN configuration？ （）ASource and destination interface must be on the same hostBSource and destination interfaces can be on different hostsCDestination vEthernet interface can be on a different VLAN than the sourceDDestination interface can be a physical portEDestination interface cannot be a physical port
考题
多选题Which two field-replaceable units FRUs are hot-swappable？（）ARouting Engine on M10iBPhysical Interface Card on M7iCfan tray on J-series routersDPhysical Interface Modules on J6300 router
考题
多选题Overlay Transport Virtualization （OTV） join interface is used to source the OTV encapsulated traffic and send it to the Layer 3 domain of the data center network. Which statements are true about OTV join interface？ （）AJoin interface is a Layer 3 entity， and with the Cisco NX-OS release 6.0， it can only be defined as a physical interface， physical subinterface， Layer 3 port channel， or Layer 3 port channel subinterface.BA single join interface can be defined and associated with a given OTV overlay.CMultiple overlays can also share the same join interface.DJoin interface can be a loopback interface.EThe join interface is a Layer 3 entity that can be defined as a physical interface but not as a logical one.
考题
多选题Which three elements must be used when you configure a router interface for vlan trunking?（）Aone IP network or subnetwork for each subinterfaceBsubinterface numbering that matches vlan tagesCsubinterface encapsulation identifiers that match vlan tagsDa management domain for each subinterfaceEone physical interface for each subinterfaceFone subinterface per vlan
热门标签
最新试卷
