网友您好, 请在下方输入框内输入要搜索的题目:

题目内容 (请给出正确答案)
单选题
Which of the listed set of conditions indicates early fuel injection timing?()
A

Loss of engine power and high exhaust temperatures

B

Higher than normal firing pressure and low exhaust temperatures

C

High fuel consumption and high exhaust temperatures

D

Lower than normal compression pressure and high exhaust temperature


参考答案

参考解析
解析: 暂无解析
更多 “单选题Which of the listed set of conditions indicates early fuel injection timing?()A Loss of engine power and high exhaust temperaturesB Higher than normal firing pressure and low exhaust temperaturesC High fuel consumption and high exhaust temperaturesD Lower than normal compression pressure and high exhaust temperature” 相关考题
考题 Which of the listed factors will indicate the most about the ability of a fuel to ignite in a diesel engine?A.ViscosityB.Sulfur contentC.Pour pointD.Cetane number

考题 The plunger in a jerk pump is rotated until the release port is uncovered If the port remains uncovered all of the time, which of the listed operations will occur?A.No fuel will be deliveredB.The maximum effective stroke will be attainedC.The fuel delivered to the cylinder will be excessiveD.The injection nozzle will overheat and carbonize

考题 A blinking green power LED indicates which of the following conditions on a Cisco Series 1000 lightweight access point?()A、lost connection to the controllerB、duplicate IP addressC、startupD、site survey mode

考题 单选题When lighting off an auxiliary boiler, which of the problems listed could cause the burners to sputter?()A cold fuel oilB low fuel oil pressureC low atomizing steam pressureD water in the fuel oil

考题 单选题Which of the conditions listed would cause simultaneous high cylinder firing pressure and low exhaust temperature?()A Improper fuel rack positioningB Lengthy opening of the exhaust valveC Excessively early injection timingD Extended light load operation

考题 单选题If you increase the clearance between a valve stem and rocker arm, which of the listed condition will occur?()A valve will open laterB valves will close laterC amount of fuel injected will be increasedD amount of fuel injected will be decreased

考题 单选题Which of the listed substances can be satisfactorily removed from diesel fuel by centrifuging?()A SludgeB GasolineC Fuel oilD Lube oil

考题 单选题Which of the listed diesel engine operating conditions should be checked immediately after any diesel engine is started?()A Exhaust temperatureB Lube oil levelC Lube oil pressureD Water level in the expansion tank

考题 单选题Which of the listed conditions will occur if a diesel engine exhaust valve is leaking?()A Loss of compression for that cylinderB Misfiring or rough runningC Damage to the valveD All of the above

考题 单选题Which of the listed cylinder liner surface conditions indicates proper lubrication?()A Dull black appearanceB Bright appearanceC Thin layer of lacquerD Thick oily film

考题 单选题Which of the listed conditions can cause lacquer to be deposited on a piston skirt?()A High sulphur content fuelB High lube oil temperaturesC High vanadium content fuelD Excessive piston slap

考题 单选题Which of the conditions listed could cause the cylinder relief valves on a large, low-speed, propulsion diesel engine to lift?()A Plugged injector nozzlesB Excessive fuel injectionC Very late injection timingD Incorrect crankshaft clearance

考题 单选题Which of the listed conditions can be considered as the single greatest cause of accidents?()A SpeedB Excessive knowledge or skillC Human errorD Excitement

考题 单选题As engine RPM is increased from idle speed to full load speed, which of the conditions listed will decrease?()A Compression ratioB Fuel/Air ratioC Compression pressureD Lube oil pressure

考题 单选题Which of the listed conditions can be used to determine if lube oil has been diluted by fuel? ()A Viscosity is decreasedB Octane number is alteredC Pump speed is decreasedD Blower’s speed is decreased

考题 单选题Which of the following conditions indicates the dilution of diesel engine lube oil by fuel oil?()A Water discharging from the water outlet of the lube oil purifierB Fuel oil discharging from the water outlet of the lube oil purifierC Lube oil discharging from the water outlet of the lube oil purifierD A change in the lube oil viscosity

考题 单选题Which of the items listed causes a direct acting mechanical governor to operate the engine fuel control linkage?()A Hydraulic oil pressureB Servomotor actionC Flyweight centrifugal forceD Relay motion

考题 单选题Which of the following conditions could be a cause of excessive fuel dilution of diesel engine lube oil?()A Leaking fuel injectorsB Lower than normal compressionC Delayed fuel injectionD All of the above are correct

考题 单选题Which of the conditions listed represents the greatest effect of excess frost accumulation on the evaporator coils?()A Keeps the refrigerated space coolerB Reduces the efficiency of the plantC Takes the load off the compressorD Has no affect on the system

考题 单选题A blinking green led indicates which of the following conditions on a cisco 1030 remote edge ap?()A startupB site survey modeC lost connection to the controllerD duplicate ip address

考题 单选题Which of the listed factors will indicate the most about the ability of a fuel to ignite in a diesel engine?()A ViscosityB Sulfur contentC Pour pointD Cetane number

考题 单选题Which of the substances listed is satisfactorily removed from the fuel by a centrifugal oil purifier?()A Carbon particlesB Lube oilC GasolineD Diesel fuel

考题 单选题A blinking green LED indicates which of the following conditions on a Cisco 1030 Remote EdgeAP?()A startupB site survey modeC lost connection to the controllerD duplicate IP address

考题 单选题When a fuel injection nozzle overheats, which of the problems listed can be expected?()A The fuel metering will varyB The fuel will explodeC The cylinder head will crackD The engine will stop

考题 单选题Which of the substances listed is satisfactorily removed from the fuel by a centrifugal oil purifier?()A ImpuritiesB Lube oilC GasolineD Diesel fuel

考题 单选题Which of the listed conditions will affective pressure the most in the cylinder of a diesel engine?()A TBN of the lubricating oilB Temperature of the lube oilC Completeness in the mixing of the fuel and airD Temperature of the cooling (sea) water