网友您好, 请在下方输入框内输入要搜索的题目:
题目内容
(请给出正确答案)
Which IOS commands can a network technician use to verify all RIP, IGRP,EIGRP, and OSPF routing protocol configurations?()
A. debug ip routing
B. show running-config
C. show ip route protocols
D. show ip protocols
E. show protocols al
参考答案
更多 “ Which IOS commands can a network technician use to verify all RIP, IGRP,EIGRP, and OSPF routing protocol configurations?() A. debug ip routingB. show running-configC. show ip route protocolsD. show ip protocolsE. show protocols al ” 相关考题
考题
Which three route filtering statements are true?()
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
考题
A network administrator is designing a Cisco network for a large company. The network must be able to use minimal bandwidth for routing updates, converge quickly, and support VLSM, CIDR, IP and IPX. Which routing protocol will best fit the requirements of this network?()A. RIP v1B. RIP v2C. IGRPD. OSPFE. EIGRP
考题
A routing table contains static, RIP, and IGRP routes destined to the same network with each route set to its default administrative distance. Which route will be the preferred route?()
A. The RIP routeB. The static routeC. The IGRP routeD. All three will load balance.
考题
Which routing protocols can be used within the enterprise network shown in the diagram?()
A.RIP v1B.RIP v2C.IGRPD.OSPFE.BGPF.EIGRP
考题
Open Shortest Path First (OSPF) was designed as an ( ) gateway protocol, for use in an autonomous system such as a local area network (LAN). It implements Dijkstra's algorithm, also known as the ( ) path first algorithm. As a link-state routing protocol it was based on the link-state algorithm developed for the ARPANET in 1980 and the IS-IS routing protocol. OSPF was first standardised in 1989 as RFC 1131, which is now known as OSPF version 1.Routing protocols like OSPF calculate the shortest route to a destination through the network based on an algorithm. The first routing protocol that was widely implemented, the (请作答此空), calculated the shortest route based on hops, that is the number of routers that an IP packet had to traverse to reach the destination host. RIP successfully implemented dynamic routing, where routing tables change if the network topology changes. But RIP did not adapt its routing according to changing network conditions, such as data-transfer rate. Demand grew for a dynamic routing protocol that could calculate the fastest route to a destination. ( ) was developed so that the shortest path through a network was calculated based on the cost of the route, taking into account bandwidth, delay and load. Therefore OSPF undertakes route cost calculation on the basis of link-cost parameters, which can be weighted by the administrator. OSPF was quickly adopted because it became known for reliably calculating routes through large and complex local area networks.As a link state routing protocol, OSPF maintains link state ( ), which are really network topology maps, on every router on which it is implemented. The state of a given route in the network is the cost, and OSPF algorithm allows every router to calculate the cost of the routes to any given reachable destination. Unless the administrator has made a configuration, the link cost of a path connected to a router is determined by the bit rate (1 Gbit/s, 10 Gbit/s, etc) of the interface. A router interface with OSPF will then advertise its link cost to neighbouring routers through multicast, known as the hello procedure. All routers with OSPF implementation keep sending hello packets, and thus changes in the cost of their links become known to neighbouring routers. The information about the cost of a link, that is the speed of a point to point connection between two routers, is then cascaded through the network because OSPF routers advertise the information they receive from one neighbouring router to all other neighbouring routers. This process of flooding link state information through the network is known as synchronisation. Based on this information, all routers with OSPF implementation continuously update their link state databases with information about the network topology and adjust their routing tables.OSPF has become a popular dynamic routing protocol. Other commonly used dynamic routing protocols are the RIP and the Border Gateway Protocol (BGP). Today routers support at least one interior gateway protocol to advertise their routing tables within a local area network. Frequently implemented interior gateway protocols besides OSPF are RIP, IS-IS, and the proprietary Interior Gateway Routing Protocol (IGRP) by Cisco.A.OSPF
B.RIP
C.IS-IS
D.EIGRP
考题
Open Shortest Path First (OSPF) was designed as an ( ) gateway protocol, for use in an autonomous system such as a local area network (LAN). It implements Dijkstra's algorithm, also known as the ( ) path first algorithm. As a link-state routing protocol it was based on the link-state algorithm developed for the ARPANET in 1980 and the IS-IS routing protocol. OSPF was first standardised in 1989 as RFC 1131, which is now known as OSPF version 1.Routing protocols like OSPF calculate the shortest route to a destination through the network based on an algorithm. The first routing protocol that was widely implemented, the ( ), calculated the shortest route based on hops, that is the number of routers that an IP packet had to traverse to reach the destination host. RIP successfully implemented dynamic routing, where routing tables change if the network topology changes. But RIP did not adapt its routing according to changing network conditions, such as data-transfer rate. Demand grew for a dynamic routing protocol that could calculate the fastest route to a destination. ( ) was developed so that the shortest path through a network was calculated based on the cost of the route, taking into account bandwidth, delay and load. Therefore OSPF undertakes route cost calculation on the basis of link-cost parameters, which can be weighted by the administrator. OSPF was quickly adopted because it became known for reliably calculating routes through large and complex local area networks.As a link state routing protocol, OSPF maintains link state (请作答此空), which are really network topology maps, on every router on which it is implemented. The state of a given route in the network is the cost, and OSPF algorithm allows every router to calculate the cost of the routes to any given reachable destination. Unless the administrator has made a configuration, the link cost of a path connected to a router is determined by the bit rate (1 Gbit/s, 10 Gbit/s, etc) of the interface. A router interface with OSPF will then advertise its link cost to neighbouring routers through multicast, known as the hello procedure. All routers with OSPF implementation keep sending hello packets, and thus changes in the cost of their links become known to neighbouring routers. The information about the cost of a link, that is the speed of a point to point connection between two routers, is then cascaded through the network because OSPF routers advertise the information they receive from one neighbouring router to all other neighbouring routers. This process of flooding link state information through the network is known as synchronisation. Based on this information, all routers with OSPF implementation continuously update their link state databases with information about the network topology and adjust their routing tables.OSPF has become a popular dynamic routing protocol. Other commonly used dynamic routing protocols are the RIP and the Border Gateway Protocol (BGP). Today routers support at least one interior gateway protocol to advertise their routing tables within a local area network. Frequently implemented interior gateway protocols besides OSPF are RIP, IS-IS, and the proprietary Interior Gateway Routing Protocol (IGRP) by Cisco.A.table
B.databases
C.maps
D.topology
考题
Open Shortest Path First (OSPF) was designed as an (请作答此空) gateway protocol, for use in an autonomous system such as a local area network (LAN). It implements Dijkstra's algorithm, also known as the ( ) path first algorithm. As a link-state routing protocol it was based on the link-state algorithm developed for the ARPANET in 1980 and the IS-IS routing protocol. OSPF was first standardised in 1989 as RFC 1131, which is now known as OSPF version 1.Routing protocols like OSPF calculate the shortest route to a destination through the network based on an algorithm. The first routing protocol that was widely implemented, the ( ), calculated the shortest route based on hops, that is the number of routers that an IP packet had to traverse to reach the destination host. RIP successfully implemented dynamic routing, where routing tables change if the network topology changes. But RIP did not adapt its routing according to changing network conditions, such as data-transfer rate. Demand grew for a dynamic routing protocol that could calculate the fastest route to a destination. ( ) was developed so that the shortest path through a network was calculated based on the cost of the route, taking into account bandwidth, delay and load. Therefore OSPF undertakes route cost calculation on the basis of link-cost parameters, which can be weighted by the administrator. OSPF was quickly adopted because it became known for reliably calculating routes through large and complex local area networks.As a link state routing protocol, OSPF maintains link state ( ), which are really network topology maps, on every router on which it is implemented. The state of a given route in the network is the cost, and OSPF algorithm allows every router to calculate the cost of the routes to any given reachable destination. Unless the administrator has made a configuration, the link cost of a path connected to a router is determined by the bit rate (1 Gbit/s, 10 Gbit/s, etc) of the interface. A router interface with OSPF will then advertise its link cost to neighbouring routers through multicast, known as the hello procedure. All routers with OSPF implementation keep sending hello packets, and thus changes in the cost of their links become known to neighbouring routers. The information about the cost of a link, that is the speed of a point to point connection between two routers, is then cascaded through the network because OSPF routers advertise the information they receive from one neighbouring router to all other neighbouring routers. This process of flooding link state information through the network is known as synchronisation. Based on this information, all routers with OSPF implementation continuously update their link state databases with information about the network topology and adjust their routing tables.OSPF has become a popular dynamic routing protocol. Other commonly used dynamic routing protocols are the RIP and the Border Gateway Protocol (BGP). Today routers support at least one interior gateway protocol to advertise their routing tables within a local area network. Frequently implemented interior gateway protocols besides OSPF are RIP, IS-IS, and the proprietary Interior Gateway Routing Protocol (IGRP) by Cisco.A.exterior
B.interior
C.border
D.routing
考题
A network administrator is designing a Cisco network for a large company. The network must be able to use minimal bandwidth for routing updates, converge quickly, and support VLSM, CIDR, IP and IPX. Which routing protocol will best fit the requirements of this network?()A、RIP v1B、RIP v2C、IGRPD、OSPFE、EIGRP
考题
A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network()。A、The router will use the static route.B、The router will use the OSPF route.C、The router will use the EIGRP route.D、The router will load balance and use all three routes.
考题
A routing table contains static, RIP, and IGRP routes destined to the same network with each route set to its default administrative distance. Which route will be the preferred route?()A、The RIP routeB、The static routeC、The IGRP routeD、All three will load balance.
考题
A router simultaneously receives all the following routes in various routing updates. Which of thefollowing routes would end up in the routing table?(Choose all that apply.)()A、RIP route 10.1.2.0/24B、EIGRP route 10.1.2.0/24C、RIP route 10.1.0.0/16D、OSPF route 10.1.0.0/16E、RIP route 10.0.0.0/16F、OSPF route 10.1.2.0/24
考题
Which two statements about route redistribution when implementing OSPF are true?()A、Routes learned using any IP routing protocol can only be redistributed into non IP routing protocols.B、OSPF can import routes learned using EIGRP, RIP, and IS - IS.C、OSPF routes cannot be exported into EIGRP, RIP, an d IS - IS.D、At the interdomain level, OSPF cannot import routes learned using BGP.E、OSPF routes can be exported into BGP.
考题
How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)()。A、If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.B、If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.C、If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.D、If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.E、If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.F、If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
考题
A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?()A、The router will use the static route.B、The router will use the OSPF route.C、The route will use the EIGRP route.D、The router will load balance and use all three routes.
考题
Which statement about the ip classless router command is true?()A、The ip classless command is enabled by default in recent versions of IOS.B、The ip classless command should only be enabled when static routing is being used instead of a routing protocol.C、The ip classless command should be enabled by the network administrator whenever RIPv1 or IGRP is being used.D、The ip classless command should be enabled by the network administrator whenever OSPF, RIPv2, or EIGRP is being used.
考题
Which IOS commands can a network technician use to verify all RIP, IGRP,EIGRP, and OSPF routing protocol configurations?()A、debug ip routingB、show running-configC、show ip route protocolsD、show ip protocolsE、show protocols al
考题
Which three route filtering statements are true?()A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
考题
You are a network administrator for your company. The network consists of a single Active Directory domain. All servers run Windows Server 2003. The company’s main office is in Barcelona, and it has branch offices in Paris and London. The company has no immediate plans to expand or relocate the offices. The company wants to connect the office networks by using a frame relay WAN connection and Routing and Remote Access servers that are configured with frame relay WAN adapters. Computers in each office will be configured to use the local Routing and Remote Access server as a default gateway. You are planning the routing configuration for the Routing and Remote Access servers. You need to allow computers in Barcelona, Paris, and London to connect to computers in any office. You want to minimize routing traffic on the WAN connection. What should you do? ()A、 At each office, add the OSPF routing protocol to Routing and Remote Access, add the WAN adapter to the OSPF routing protocol, and deploy OSPF as a single-area internetwork.B、 At each office, add the RIP version 2 routing protocol to Routing and Remote Access, and configure the WAN adapter to use RIP version 2. Configure the outgoing packet protocol as RIP version 2 broadcast and the incoming packet protocol as RIP version 1 and 2.C、 At each office, add the RIP version 2 routing protocol to Routing and Remote Access, and configure the WAN adapter to use RIP version 2. Configure the outgoing packet protocol as RIP version 2 multicast and the incoming packet protocol as RIP version 2 only.D、 At each office, configure the Routing and Remote Access server with static routes to the local networks at the other two offices.
考题
单选题You are a network administrator for your company. The network consists of a single Active Directory domain. All servers run Windows Server 2003. The company’s main office is in Barcelona, and it has branch offices in Paris and London. The company has no immediate plans to expand or relocate the offices. The company wants to connect the office networks by using a frame relay WAN connection and Routing and Remote Access servers that are configured with frame relay WAN adapters. Computers in each office will be configured to use the local Routing and Remote Access server as a default gateway. You are planning the routing configuration for the Routing and Remote Access servers. You need to allow computers in Barcelona, Paris, and London to connect to computers in any office. You want to minimize routing traffic on the WAN connection. What should you do? ()A
At each office, add the OSPF routing protocol to Routing and Remote Access, add the WAN adapter to the OSPF routing protocol, and deploy OSPF as a single-area internetwork.B
At each office, add the RIP version 2 routing protocol to Routing and Remote Access, and configure the WAN adapter to use RIP version 2. Configure the outgoing packet protocol as RIP version 2 broadcast and the incoming packet protocol as RIP version 1 and 2.C
At each office, add the RIP version 2 routing protocol to Routing and Remote Access, and configure the WAN adapter to use RIP version 2. Configure the outgoing packet protocol as RIP version 2 multicast and the incoming packet protocol as RIP version 2 only.D
At each office, configure the Routing and Remote Access server with static routes to the local networks at the other two offices.
考题
多选题Which two statements about route redistribution when implementing OSPF are true?()ARoutes learned using any IP routing protocol can only be redistributed into non IP routing protocols.BOSPF can import routes learned using EIGRP, RIP, and IS - IS.COSPF routes cannot be exported into EIGRP, RIP, an d IS - IS.DAt the interdomain level, OSPF cannot import routes learned using BGP.EOSPF routes can be exported into BGP.
考题
单选题A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?()A
The router will use the static route.B
The router will use the OSPF route.C
The route will use the EIGRP route.D
The router will load balance and use all three routes.
考题
单选题Which statement about the ip classless router command is true?()A
The ip classless command is enabled by default in recent versions of IOS.B
The ip classless command should only be enabled when static routing is being used instead of a routing protocol.C
The ip classless command should be enabled by the network administrator whenever RIPv1 or IGRP is being used.D
The ip classless command should be enabled by the network administrator whenever OSPF, RIPv2, or EIGRP is being used.
考题
多选题How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)()。AIf RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.BIf RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.CIf EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.DIf EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.EIf EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.FIf EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
考题
多选题Which IOS commands can a network technician use to verify all RIP, IGRP,EIGRP, and OSPF routing protocol configurations?()Adebug ip routingBshow running-configCshow ip route protocolsDshow ip protocolsEshow protocols al
热门标签
最新试卷