网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）
- A、The switch port link lights will be off on both switches indicating the ports are not connected.
- B、The switch port link light will be off on one switch indicating that STP has disabled the port.
- C、The switch port link lights will flash amber indicating an error.
- D、The switch port link lights will be green indicating normal operation.
参考答案
更多 “A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）A、The switch port link lights will be off on both switches indicating the ports are not connected.B、The switch port link light will be off on one switch indicating that STP has disabled the port.C、The switch port link lights will flash amber indicating an error.D、The switch port link lights will be green indicating normal operation.” 相关考题
考题
You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?A．Switch(config)# switchport trunk encapsulation islB．Switch(config)# switchport trunk encapsulation ietfC．Switch(config-if)# switchport trunk encapsulation islD．Switch(config-if)# switchport trunk encapsulation ietfE．Switch(config-if)# switchport trunk encapsulation dot1q
考题
An administrator is having a hard time adding a new switch to the network. After verifying that allthe ports are configured correctly on each switch, which of the following should the administratorverily NEXT?（）A. Straight-through cable is used to connect both switchesB. Loopback plug is connectedC. Crossover cable is used to connect both switchesD. Cable is a rollover cable
考题
You want your Catalyst switch to implement a switching method that holds a packet in its memory until the data portion of the respected packet reaches the switch.Which method should you employ on your Catalyst switch?（）A. Fast ForwardB. Store and forwardC. Frag-freeD. None of the above
考题
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method.When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A. Switch(config)# switchport trunk encapsulation islB. Switch(config)# switchport trunk encapsulation ietfC. Switch(config-if)# switchport trunk encapsulation islD. Switch(config-if)# switchport trunk encapsulation ietfE. Switch(config-if)# switchport trunk encapsulation dot1q
考题
You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A、 Catalyst 2960 SeriesB、 Catalyst 3750 SeriesC、 Catalyst 4900 SeriesD、 Catalyst 6500 Series
考题
Which statement correctly describes network security settings in Cisco Network Assistant for the Catalyst Express 500 Switch？（）A、The LOW setting enables broadcast storm control， but has no effect on the number of devices that can connect to a switch portB、The LOW setting enables broadcast storm control and limits the number of devices that can connect to a switch port.C、The LOW setting disables broadcast storm control but limits the number of devices that can connect to a switch portD、The default network setting is "HIGH"
考题
A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）A、The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.B、The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C、The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.D、The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
考题
You want your Catalyst switch to implement a switching method that holds a packet in its memory until the data portion of the respected packet reaches the switch.Which method should you employ on your Catalyst switch?（）A、Fast ForwardB、Store and forwardC、Frag-freeD、None of the above
考题
The following Cisco Catalyst Series switches fit in the access area. Which switches also utilize StackWise technology to address the needs of companies with growing networks by allowing them to connect multiple units？（）A、 Cisco Express Catalyst 500 Series switchesB、 Cisco Catalyst 2900 Series switchesC、 Cisco Catalyst 3560 switchesD、 Cisco Catalyst 3700 Series switchesE、 Cisco Catalyst 4500 Series switchesF、 Cisco Catalyst 6500 Series switches
考题
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A、Switch(config)# switchport trunk encapsulation islB、Switch(config)# switchport trunk encapsulation ietfC、Switch(config-if)# switchport trunk encapsulation islD、Switch(config-if)# switchport trunk encapsulation ietfE、Switch(config-if)# switchport trunk encapsulation dot1q
考题
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network?（）A、One router is running RIPv1.B、RIP neighbor is 224.0.0.9.C、The network contains a loop.D、Network 10.10.1.0 is reachable.
考题
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?（）A、Lower the bridge priority number.B、Change the MAC address of the switch.C、Increase the VTP revision number for the domain.D、Lower the root path cost on the switch ports.E、Assign the switch an IP address with the lowest value.
考题
The following Cisco Catalyst Series switches fit in the access area. Which switches also utilize StackWise technology to address the needs of companies with growing networks by allowing them to connect？（）A、 Cisco Express Catalyst 500 Series switchesB、 Cisco Catalyst 2900 Series switchesC、 Cisco Catalyst 3560 switchesD、 Cisco Catalyst 3700 Series switchesE、 Cisco Catalyst 4500 Series switchesF、 Cisco Catalyst 6500 Series switches
考题
What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）A、The switch will ignore VTP summary advertisementsB、The switch will forward VTP summary advertisementsC、The switch will process VTP summary advertisementsD、The switch will originate VTP summary advertisementsE、The switch will create, modify and delete VLANs for the entire VTP domain
考题
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
考题
A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）A、CAT3 cableB、Serial cableC、Crossover cableD、Rollover cable
考题
A user is unable to connect to the network. A network technician is able to determine that there is a problem on the switch. All other users on that switch are able to connect successfully to the network. Which of the following is a probable cause？（）A、Switching loop is occurring on the switch.B、Wrong subnet mask on the switch.C、Incorrect SNMP settings on the switch.D、Port is misconfigured on the switch.
考题
An administrator is having a hard time adding a new switch to the network. After verifying that allthe ports are configured correctly on each switch, which of the following should the administratorverily NEXT?（）A、Straight-through cable is used to connect both switchesB、Loopback plug is connectedC、Crossover cable is used to connect both switchesD、Cable is a rollover cable
考题
单选题You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A
Switch(config)# switchport trunk encapsulation islB
Switch(config)# switchport trunk encapsulation ietfC
Switch(config-if)# switchport trunk encapsulation islD
Switch(config-if)# switchport trunk encapsulation ietfE
Switch(config-if)# switchport trunk encapsulation dot1q
考题
单选题A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）A
The switch port link lights will be off on both switches indicating the ports are not connected.B
The switch port link light will be off on one switch indicating that STP has disabled the port.C
The switch port link lights will flash amber indicating an error.D
The switch port link lights will be green indicating normal operation.
考题
多选题You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）AThe switch name must match the workgroup name of the local network.BThe switch must be configured with an IP address and default gateway.CThe remote workstations must have access to the management VLAN of the switch.DCDP must be enabled on the switch so that it can be located by other devices on the network.
考题
单选题A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）A
The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.B
The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C
The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.D
The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
考题
单选题You need to connect two Company core switches via an ISL trunk. Which statement is true regarding the configuration of ISL trunks？ （）A
A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.B
All Catalyst switches support ISL trunking.C
A Catalyst switch will report giants if one side is configured for ISL while the other side is not.D
ISL trunking requires that native VLANs match.E
None of the other alternatives apply
考题
单选题The following Cisco Catalyst Series switches fit in the access area. Which switches also utilize StackWise technology to address the needs of companies with growing networks by allowing them to connect？（）A
Cisco Express Catalyst 500 Series switchesB
Cisco Catalyst 2900 Series switchesC
Cisco Catalyst 3560 switchesD
Cisco Catalyst 3700 Series switchesE
Cisco Catalyst 4500 Series switchesF
Cisco Catalyst 6500 Series switches
考题
单选题The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network？（）A
Lower the bridge priority number.B
Change the MAC address of the switch.C
Increase the VTP revision number for the domain.D
Lower the root path cost on the switch ports.E
Assign the switch an IP address with the lowest value.
考题
单选题You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A
Catalyst 2960 SeriesB
Catalyst 3750 SeriesC
Catalyst 4900 SeriesD
Catalyst 6500 Series
考题
单选题Which statement correctly describes network security settings in Cisco Network Assistant for the Catalyst Express 500 Switch？（）A
The LOW setting enables broadcast storm control， but has no effect on the number of devices that can connect to a switch portB
The LOW setting enables broadcast storm control and limits the number of devices that can connect to a switch port.C
The LOW setting disables broadcast storm control but limits the number of devices that can connect to a switch portD
The default network setting is HIGH
热门标签
最新试卷
