网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
多选题
Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）
A
It is achieved by using more than one HSRP group.
B
It is done in regards to either round robin or weight basis.
C
It is used to offload the active router in a certain HSRP group.
D
The return traffic is influenced by HSRP load sharing configuration.
E
Single group HSRP is used to achieve more efficient link utilization.
参考答案
参考解析
解析：
暂无解析
更多 “多选题Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）AIt is achieved by using more than one HSRP group.BIt is done in regards to either round robin or weight basis.CIt is used to offload the active router in a certain HSRP group.DThe return traffic is influenced by HSRP load sharing configuration.ESingle group HSRP is used to achieve more efficient link utilization.” 相关考题
考题
HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network.Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)A. a shared single interfaceB. the ability to track serial interfacesC. UDP-based hello packetsD. the impact of flapping links if timers are too low
考题
Which three of the following network features are methods used to achieve high availability()
A.Spanning Tree Protocol（STP）B.Delay reductionC.Hot Standby Routing Protocol（HSRP）D.Dynamic routing protocolsE.Quality of Service（QoS）F.Jitter management
考题
Which three best practices should be implemented at the campus backbone submodule to support the server farm module?()
A. Implement highly redundant switching and links with no single points or paths of failure.B. Implement server load balancing.C. Implement the Hot Standby Router Protocol (HSRP) for failover protection.D. Implement intrusion detection with automatic notification of intrusion attempts in place.
考题
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this？ （）A、 en standby preemptB、 standby preempt enableC、 standby preemptD、 hot standby preempt
考题
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
考题
Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）A、It is achieved by using more than one HSRP group.B、It is done in regards to either round robin or weight basis.C、It is used to offload the active router in a certain HSRP group.D、The return traffic is influenced by HSRP load sharing configuration.E、Single group HSRP is used to achieve more efficient link utilization.
考题
What three tasks must a network administrator perform to properly configure Hot Standby Routing Protocol （HSRP）？（）A、 Define the encapsulation type.B、 Define the standby router.C、 Define the standby IP address.D、 Enable the standby priority.
考题
HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)A、a shared single interfaceB、the ability to track serial interfacesC、UDP-based hello packetsD、the impact of flapping links if timers are too low
考题
Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router？（）A、 activeB、 speakC、 learnD、 listenE、 initF、 standby
考题
Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.B、 The default priority of a router is zero （0）.C、 The no standby priority command assigns a priority of 100 to the router.D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
考题
Which three of the following network features are methods used to achieve high availability（）A、Spanning Tree Protocol（STP）B、Delay reductionC、Hot Standby Routing Protocol（HSRP）D、Dynamic routing protocolsE、Quality of Service（QoS）F、Jitter management
考题
You need to decide on the best router redundancy protocol to use in the Company network. Which two statements are true about HSRP， VRRP， and GLBP？（）A、 GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.B、 HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.C、 GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.D、 Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.E、 GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
考题
You have configured router R1 with HSRP， using the standard defaults. Which three statements are true of a default HSRP configuration？（）A、 The Standby hello time is 2 seconds.B、 Two HSRP groups are configured.C、 The Standby track interface priority is 10.D、 The Standby hold time is 10 secondsE、 The Standby priority is 100.F、 The Standby delay is 3 seconds.
考题
Which statement correctly describes IPsec VPN backup technology？（）A、The cypto isakmp keepalive command is used to configure the Stateful Switchover （SSO）protocolB、Reverse Route Injection （RRI） is configured on at the remote site to inject the central sitenetworksC、Each Hot Standby Routing Protocol （HSRP） standby group has two well-known MACaddresses and a virtual IP addressD、The cypto isakmp keepalive command is used to configure stateless failover
考题
For the following protocols， which one provides a mechanism to transparently intercept and redirect CIFS traffic from a client to a local Cisco Wida Area Application engine？（）A、Virtual Router Redundancy Protocol（VRRP）B、File Transport Protocol（FTP）C、Hot Standby Routing Protocol（HSRP）D、Web Cache Communication Protocol（WCCP）
考题
Which three best practices should be implemented at the campus backbone submodule to supportthe server farm module？ （）A、 Implement highly redundant switching and links with no single points or paths of failure.B、 Implement server load balancing.C、 Implement the Hot Standby Router Protocol （HSRP） for failover protection.D、 Implement intrusion detection with automatic notification of intrusion attempts in place.
考题
单选题You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this？ （）A
en standby preemptB
standby preempt enableC
standby preemptD
hot standby preempt
考题
多选题Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）ALoad sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.BRouters configured for HSRP can belong to multiple groups and multiple VLANs.CLoad sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.DAll routers configured for HSRP load balancing must be configured with the same priority.ERouters configured for HSRP must belong to only one group per HSRP interface.
考题
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？ （）A
physical layer issuesB
no spanning tree loopsC
use of non-default HSRP timersD
failure to set the command standby 35 preempt
考题
单选题Which of the following HSRP router states does an active router enter when it is preempted by a higher priority router？（）A
activeB
speakC
learnD
listenE
initF
standby
考题
单选题For the following protocols， which one provides a mechanism to transparently intercept and redirect CIFS traffic from a client to a local Cisco Wida Area Application engine？（）A
Virtual Router Redundancy Protocol（VRRP）B
File Transport Protocol（FTP）C
Hot Standby Routing Protocol（HSRP）D
Web Cache Communication Protocol（WCCP）
考题
多选题You need to decide on the best router redundancy protocol to use in the Company network. Which two statements are true about HSRP， VRRP， and GLBP？（）AGLBP and VRRP allow for MD5 authentication， whereas HSRP does not.BHSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.CGLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.DUnlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.EGLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
考题
多选题HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)Aa shared single interfaceBthe ability to track serial interfacesCUDP-based hello packetsDthe impact of flapping links if timers are too low
考题
单选题Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）A
physical layer issuesB
no spanning tree loopsC
use of non-default HSRP timersD
failure to set the command standby 35 preempt
考题
多选题Which three of the following network features are methods used to achieve high availability？（）ASpanning Tree Protocol （STP）BDelay reductionCHot Standby Routing Protocol （HSRP）DDynamic routing protocolsEQuality of Service （QoS）FJitter management
考题
多选题You have configured router R1 with HSRP， using the standard defaults. Which three statements are true of a default HSRP configuration？（）AThe Standby hello time is 2 seconds.BTwo HSRP groups are configured.CThe Standby track interface priority is 10.DThe Standby hold time is 10 secondsEThe Standby priority is 100.FThe Standby delay is 3 seconds.
考题
多选题Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）AIt is achieved by using more than one HSRP group.BIt is done in regards to either round robin or weight basis.CIt is used to offload the active router in a certain HSRP group.DThe return traffic is influenced by HSRP load sharing configuration.ESingle group HSRP is used to achieve more efficient link utilization.
考题
单选题Which statement correctly describes IPsec VPN backup technology？（）A
The cypto isakmp keepalive command is used to configure the Stateful Switchover （SSO）protocolB
Reverse Route Injection （RRI） is configured on at the remote site to inject the central sitenetworksC
Each Hot Standby Routing Protocol （HSRP） standby group has two well-known MACaddresses and a virtual IP addressD
The cypto isakmp keepalive command is used to configure stateless failover
热门标签
最新试卷
