考题
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()
A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type
考题
A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?()
A. Router(config-if)# encapsulation frame-relay q933aB. Router(config-if)# encapsulation frame-relay ansiC. Router(config-if)# encapsulation frame-relay ietfD. Router(config-if)# encapsulation frame-relay islE. None of the above
考题
You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()
A. Show interface lmiB. Show frame-relay lmiC. Show interface frame-relayD. Debug frame-relay interface.
考题
A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()
A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-typeE. frame-relay pvc
考题
Which three Layer 2 encapsulation types would be used on a WAN rather than a LAN?()
A.HDLCB.EthernetC.Token RingD.PPPE.FDDIF.Frame Relay
考题
which command allows you to verify the encapsulation type (CISCO OR IETF) for a frame relay link?()
A.show frame-relay mapB.show frame-relay lmiC.show inter serialD.show frame-relay pvc
考题
Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?()
A.show frame-relay end-to-endB.show frame-relay mapC.show frame-relay lmiD.show frame-relay pvc
考题
Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?()A、TestKRouter(config-if)# Encapsulation frame-relay dot1qB、TestKRouter(config-if)# Encapsulation frame-relay aal5snapC、TestKRouter(config-if)# Encapsulation frame-relay ietfD、TestKRouter(config-if)# Encapsulation frame-relay islE、None of the above
考题
A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()A、frame-relay arpB、frame-relay mapC、frame-relay interface-dlciD、frame-relay lmi-typeE、frame-relay pvc
考题
What does FRTP stand for?()A、Frame Relay Top PseudowireB、Frame Relay Traffic PseudowireC、Frame Relay Traffic ProtocolD、Frame Relay Traffic Policing
考题
you want to view the status of a frame relay connection. How to display the status of a Frame-Relay PVC?
考题
Acme Costume Company is connecting its manufacturing facilties to its stores with a small point-to-multipoint Frame Relay IP WAN. Little growth is expected in the network infrastructure.Up tothis point the company has been using a dial-on-demand network. Dropping WAN costs, however,have led them to consider using a high-speed WAN solution to improve access. Which two routingprotocols could you deploy to support the new larger network while keeping costs down?()A、 RIPB、 RIPv2C、 EIGRPD、 OSPF
考题
Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?()A、show frame-relay end-to-endB、show frame-relay mapC、show frame-relay lmiD、show frame-relay pvc
考题
Which Cisco IOS traffic-shaping mechanism statement is true? ()A、class-based policing is configured using the Modular QoS command-line (MQC)B、only the Frame Relay traffic-shaping (FRTS) mechanism can interact with a Frame Relay network, adapting to indications of Layer2 congestion in the WAN linksC、Distributed Traffic Shaping (DTS) is configured with the police command under the policy map configurationD、both Frame Relay traffic shaping (FRTS) and virtual IP (VIP)-based Distributed Traffic Shaping (DTS) have the ability to mark traffic
考题
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()A、frame-relay arpB、frame-relay mapC、frame-relay interface-dlciD、frame-relay lmi-type
考题
which command allows you to verify the encapsulation type CISCO OR IETF for a frame relay link?()A、show frame-relay mapB、show frame-relay lmiC、show inter serialD、show frame-relay pvc
考题
Which three Layer 2 encapsulation types would be used on a WAN rather than a LAN? ()A、HDLCB、EthernetC、Token RingD、PPPE、FDDIF、Frame Relay
考题
多选题When should traffic shaping be implemented on Frame Relay PVCs?()AWhen you want to drop excess traffic above the CIRBWhen there is a speed mismatch between the central site and the remote siteCWhen using Frame Relay SVCsDWhen over-subscribing the central site linkEWhen LLQ is implemented on the Frame Relay PVCFWhen Multilink PPP LFI is implemented on the Frame Relay PVC
考题
单选题What occurs on a Frame Relay network when the CIR is exceeded?()A
All TCP traffic is marked discard eligibleB
All UDP traffic is marked discard eligible and a BECN is sentC
All TCP traffic is marked discard eligible and a BECN is sentD
All traffic exceeding the CIR is marked discard eligible
考题
单选题Your network consists of a large hub - and - spoke Frame Relay network with a CIR of 56 kb/s foreach spoke. Which statement about the selection of a dynamic protocol is true?()A
EIGRP would be appropriate if LMI type ANS I is NOT used.B
EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas.C
EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.D
EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.
考题
单选题Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?()A
TestKRouter(config-if)# Encapsulation frame-relay dot1qB
TestKRouter(config-if)# Encapsulation frame-relay aal5snapC
TestKRouter(config-if)# Encapsulation frame-relay ietfD
TestKRouter(config-if)# Encapsulation frame-relay islE
None of the above
考题
单选题You are working with a client to deploy QoS on their Frame Relay WAN. They would like to be able to allow packets to cross the Frame Relay WAN but have them marked as discard eligible if they exceed the QoS policy. How would you accomplish this task?()A
Configure a class map that sets the DE bit so that the policy map can correctly apply a violate-action if the policy is exceeded.B
Configure a service policy that sets the DE bit and apply it to the serial interface connected to the Frame Relay WAN.C
Configure a policy map that has a burst-max action of setting the DE bit if the policy is exceeded.D
Configure a policy map that has a violate-action to change the DE bit from 0 to 1.
考题
单选题What occurs on a Frame Relay network when the CIR is exceeded?()A
All TCP traffic is marked discard eligible.B
All UDP traffic is marked discard eligible and a BECN is sent.C
All TCP traffic is marked discard eligible and a BECN is sent.D
All traffic exceeding the CIR is marked discard eligible.
考题
单选题You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()A
Show interface lmiB
Show frame-relay lmiC
Show interface frame-relayD
Debug frame-relay interface.
考题
单选题A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?()A
Router(config-if)# encapsulation frame-relay q933aB
Router(config-if)# encapsulation frame-relay ansiC
Router(config-if)# encapsulation frame-relay ietfD
Router(config-if)# encapsulation frame-relay islE
None of the above
考题
问答题you want to view the status of a frame relay connection. How to display the status of a Frame-Relay PVC?