网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
A customer has two Ethernet Switch Modules installed in an IBM BladeCenter Enterprise chassis. The modules were configured identically. The Ethernet module in bay one was inadvertenly reset to factory defaults. Which solution returns the module to the customer-specific configuration?（）
- A、Back up the configuration from Ethernet module in bay 2 and restore it to the module in Bay 1 using the switch CLI or Web interface
- B、Swap the modules, which will automatically resynch the settings stored in the Advanced Management Module
- C、Back up the configuration of the Ethernet module in bay one and restore it to the Ethernet module in bay two using the AMM
- D、Restore the configuration from NVRAM using the Switch Module Web interface
参考答案
更多 “A customer has two Ethernet Switch Modules installed in an IBM BladeCenter Enterprise chassis. The modules were configured identically. The Ethernet module in bay one was inadvertenly reset to factory defaults. Which solution returns the module to the customer-specific configuration?（）A、Back up the configuration from Ethernet module in bay 2 and restore it to the module in Bay 1 using the switch CLI or Web interface B、Swap the modules, which will automatically resynch the settings stored in the Advanced Management Module C、Back up the configuration of the Ethernet module in bay one and restore it to the Ethernet module in bay two using the AMM D、Restore the configuration from NVRAM using the Switch Module Web interface” 相关考题
考题
The ONS 15216 is a 32－channel system. The ONS 15216 OADMs are capable of adding and dropping one, two, or four channels. How are the OADMs provisioned to add and drop specific channels?()
A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.
考题
A network administrator has installed an N7K-F248-25XP module into an existing chassis. The module is powered on， but the interfaces are all in VDC0. What is the reason for this？（） A、 The chassis needs an EPLD upgrade to support the new module type.B、 The default VDC cannot support F2 modules.C、 The interfaces must be allocated into a VDC for F2 modules only.D、 The module has failed GOLD diagnostics， and the switch has isolated the ports to protect the integrity of the system.
考题
A manufacturing customer has an IBM BladeCenter H chassis with four， HX5 with MAX5 4-socket blades installed. Each blade has the optional Fibre Channel Expansion card. The customer wants redundancy and is going to install the following configuration： （1）two Brocade 20-Port SAN Switch Modules （2）two Nortel Networks 1/10 GB Uplink ESM （3）a redundant AMM What is the minimum number of power supplies needed for this configuration to have full redundancy？（）A、4B、3C、2D、8
考题
A customer wants to implement the following Blades in BladeCenter H:Two POWER Blades running IBM i partitions.Two POWER Blades running AIX and LinuxFour x86 Blades running Windows. Which of the following design consideration statements is correct?（）A、The Blades must use the same CIOv and CFFh expansion adapter types.B、Two physical BladeCenter H chassis will be required. One for the POWER Blades, the other for the x86 Blades.C、The x86 Blades and POWER Blades may use different expansion adapters provided the POWER Blades are in bays 1-7 and the x86 Blades are in slots 8-14.D、The x86 Blades and POWER Blades may use different expansion adapters, provided the corresponding I/O modules to Blade midplane connections are configured in the Advanced Management Module (AMM).
考题
A banking customer has two Ethernet Switch Modules installed in an IBM BCE chassis. The modules were configured identically. The Ethernet module in bay 1 was accidentally reset to factory defaults. Which solution returns the module to the customer-specific configuration? （）A、Restore the configuration from NVRAM using the Switch Module Web interface B、Back up the configuration of the Ethernet module in bay 1 and restore it to the Ethernet module in bay 2 using the AMM C、Swap the modules, which will automatically resynch the settings stored in the Advanced Management Module D、Back up the configuration from Ethernet module in bay 2 and restore it to the module in Bay 1 using the switch CLI or Web interface
考题
A customer wants to boot from SAN with their IBM BladeCenter infrastructure. What is required for the customer to be able to perform this？ （）A、4GB Modular Flash Drive for each Blade Server and Dual 15.8GB 2.5 Solid State Drive for each Blade Server B、Cisco Intelligent Gb Ethernet Switch Module and IBM BladeCenter Copper Pass-thru Module C、Fibre Channel Expansion Card for each Blade Server and Fibre Channel SAN Switch Module D、Cisco Intelligent Gb Ethernet Switch Module and Dual 15.8GB 2.5 Solid State Drive for each Blade Server
考题
Your customer has converted from traditional servers to BladeCenter technology and has a requirement for an RSA adapter on a new BladeCenter server. Which of the following options would you use？ （）A、Remote Supervisor Adapter II （RSA II Slimline）B、Management Module， which comes standard on the BladeCenterC、Acoustic Attenuation ModuleD、Ethernet NICs
考题
A project requires a new server to be set up with the ability to automatically fail over its Ethernet connection to a second connection if a network failure occurs. Which of the following provides greatest resiliency？（）A、Two switch ports will be needed on a switch,two Ethernet cables will be needed for theserver each connecting to two different Ethernet cards,and one IP address will be neededB、Two switch ports will be needed on two different switches two Ethernet cables will beneeded for the server each connecting to two different Ethernet cards,and one IP address will be neededC、Two switch ports will be needed on two different switches,two Ethernet cables will be needed for the server each connecting to two different Ethernet cards,two different IP addresses will be neededD、One switch port will be needed on one switch,a splitter will be needed to split the connection,two Ethernet cables will be needed for the server each connecting to two different Ethernet cards,and two different IP addresses will be needed
考题
Companycom is about to purchase a POWER5 Enterprise server which requires two Ethernet ports and two disks for each of the four LPARs. It has been configured and validated using the IBM eConfig tool. Which of the following is very important to verify in addition to the eConfig validation?（）A、Total number of SCSI adaptersB、Total number of Ethernet adaptersC、Total number of Ethernet adapters and number of SCSI paths per LPARD、Total number of SCSI paths available and total number of SCSI adapters
考题
When configuring unified ports on a 5548 switch， which port ordering must be respected？（）A、 Fibre Channel ports must be configured from the first port in the module.B、 Ethernet ports must be configured from the last port in the module.C、 Fibre Channel ports must be configured from the last port in the module.D、 Ethernet ports must be configured from the first port in the module.
考题
A customer has purchased a triple channel memory kit containing three DDR3 RAM modules. Theserver the RAM is intended for only has a dual channel capable motherboard. Which of the following is the BEST action to perform？（）A、Install only two modules as the RAM has to be installed in pairsB、Purchase one additional RAM module to make it even. Three modules will function as triplechannel and the additional module will be for parityC、Purchase dual channel memory. The triple channel memory may be incompatible with theserver motherboardD、Install the RAM.Two modules will perform as dual channel and one as single channel
考题
A banking customer deployed an IBM BladeCenter chassis with one Brocade 8Gb SAN switch module. The customer requires an 8Gb uplink or higher. Which configuration will meet this request?（）A、Brocade Enterprise 20-port 8Gb SAN switch module B、Brocade 20-port 8Gb SAN switch module and Brocade Advanced Performance Monitoring for IBM BladeCenter share C、Brocade Enterprise 10-port 8Gb SAN switch module D、Brocade 10-port 8Gb SAN switch module and Brocade Advanced Performance Monitoring for IBM BladeCenter
考题
A retail customer installs a BladeCenter into an existing 10/100 Ethernet network. Due to cost considerations, the customer uses Copper Pass-thru Modules. After installing this solution, the customer finds that they have no network connectivity. Which of the following at is causing the problem?（）A、Copper Pass-thru Modules only support 1000Mb line speeds. B、Spanning Tree has been enabled on the Copper Pass-thru Module. C、The customer does not have the latest firmware loaded on the Copper Pass-thru Module. D、The customer is using LS21 Blades
考题
A customer asks which bays they could install Multi-Switch Interconnect Module (MSIM). Which of the following is the source of this information?（）A、CDAT B、IBM Systems Director C、Tivoli Provisioning Manager (TPM) D、BladeCenter Interoperability guide
考题
A project requires a new server to be set up with the ability to automatically fail over its Ethernet connection to a second connection if a network failure occurs. Which of the following provides greatest resiliency？（）A、Two switch ports will be needed on a switch， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， and one IP address will be needed.B、Two switch ports will be needed on two different switches， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， and one IP address will be needed.C、Two switch ports will be needed on two different switches， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， two different IP addresses will be needed.D、One switch port will be needed on one switch， a splitter will be needed to split the connection， two ethernet cables will be needed for the server each connecting to two different Ethernet cards， and two different IP addresses will be needed.
考题
A prospect is considering a BladeCenter H chassis with the Multi-Switch Interconnect Modules. The number of Ethernet ports is important to them. What is the maximum number of Ethernet ports an HS22 blade server can support if the blade does not have any expansion blades attached?（）A、8 B、6 C、4 D、2
考题
A banking customer has the following requirements for an IBM BladeCenter solution with high speed fibre channel： （1）four 4-socket Microsoft SQL servers with two hot swap SAS drives （2）two physical Microsoft Active Directory Servers （3）twenty-two physical Citrix servers （4）three physical Web servers （5）one physical vCenter server （6）eight vSphere hosts Which configuration minimally satisfies these requirements？（）A、Three IBMBladeCenter S chassis， three Brocade Fibre modules， six Ethernet modulesB、Three IBMBladeCenter E chassis， three Brocade Fibre modules， six Ethernet modulesC、Four IBMBladeCenter H chassis， four QLogic Fibre Channel modules， eight Ethernet modulesD、Three IBMBladeCenter H chassis， three QLogic Fibre Channel modules， six Ethernet modules
考题
A customer wants to install an IBM BladeCenter infrastructure but is concerned about the cost of the internal fibre switches. Consequently. the customer wants to use the Optical Pass-Thru Module （OPM）. What TRUE statement should be mentioned to the customer regarding the OPM？（）A、You can not put the Optical Pass-Thru Module in the same IBM BladeCenter chassis as a Cisco Intelligent Ethernet Switch.B、Using blade servers with the Optical Pass-Thru Module will require more fibre ports on the external fibre switch.C、The Optical Pass-Thru Module does not provide the customer with an opportunity to reuse their fibre switch.D、The blade servers do not work with the Optical Pass-Thru Module.
考题
A media customer has an IBM BladeCenter E with ten HS22 Blade server installed. Currently only one Ethernet port is available for each server. What is required to enable the second port on eachserver？（）A、Fiber Channel Switch ModuleB、Gb Ethernet expansion cardC、Myrinet Cluster expansion cardD、Ethernet Switch Module
考题
A customer is considering BladeCenter H and S chassis. Which of the following is a reason to implement BladeCenter H？（）A、Support for10Gb internal networkB、Support for SSDC、Support for integrated disk drivesD、Support for8Gb FC Switch Modules
考题
The primary line module has failed and the spare line module is nowactive.What occurs，by default，when the primary line module returns to an operational status？（）A、The primary line module is inactive for five minutes and then becomes active.B、The primary line module is in standby mode，while the spare line module remains active.C、The primary line module becomes active immediately and the spare line module becomes inactive.D、The primary and spare line modules are active for five minutes，after which time the spare line module becomes inactive.
考题
A banking customer deployed an IBM BladeCenter chassis with one Brocade 8Gb SAN switch module. The customer requires an 8Gb uplink or higher. Which configuration will meet this request of the following？（）A、Brocade Enterprise 20-port 8Gb SAN switch moduleB、Brocade 20-port8Gb SAN switch module and Brocade Advanced Performance Monitoring for IBM BladeCenterC、Brocade Enterprise 10-port 8Gb SAN switch moduleD、Brocade 10-port8Gb SAN switch module and Brocade Advanced Performance Monitoring for IBM BladeCenter
考题
单选题A network administrator has installed an N7K-F248-25XP module into an existing chassis. The module is powered on， but the interfaces are all in VDC0. What is the reason for this？（）A
The chassis needs an EPLD upgrade to support the new module type.B
The default VDC cannot support F2 modules.C
The interfaces must be allocated into a VDC for F2 modules only.D
The module has failed GOLD diagnostics， and the switch has isolated the ports to protect the integrity of the system.
考题
单选题A media customer has an IBM BladeCenter E with ten HS22 Blade server installed. Currently only one Ethernet port is available for each server. What is required to enable the second port on eachserver？（）A
Fiber Channel Switch ModuleB
Gb Ethernet expansion cardC
Myrinet Cluster expansion cardD
Ethernet Switch Module
考题
单选题A project requires a new server to be set up with the ability to automatically fail over its Ethernet connection to a second connection if a network failure occurs. Which of the following provides greatest resiliency？（）A
Two switch ports will be needed on a switch,two Ethernet cables will be needed for theserver each connecting to two different Ethernet cards,and one IP address will be neededB
Two switch ports will be needed on two different switches two Ethernet cables will beneeded for the server each connecting to two different Ethernet cards,and one IP address will be neededC
Two switch ports will be needed on two different switches,two Ethernet cables will be needed for the server each connecting to two different Ethernet cards,two different IP addresses will be neededD
One switch port will be needed on one switch,a splitter will be needed to split the connection,two Ethernet cables will be needed for the server each connecting to two different Ethernet cards,and two different IP addresses will be needed
考题
单选题The primary line module has failed and the spare line module is nowactive.What occurs，by default，when the primary line module returns to an operational status？（）A
The primary line module is inactive for five minutes and then becomes active.B
The primary line module is in standby mode，while the spare line module remains active.C
The primary line module becomes active immediately and the spare line module becomes inactive.D
The primary and spare line modules are active for five minutes，after which time the spare line module becomes inactive.
考题
单选题A retail customer installs a BladeCenter into an existing 10/100 Ethernet network. Due to cost considerations, the customer uses Copper Pass-thru Modules. After installing this solution, the customer finds that they have no network connectivity. Which of the following at is causing the problem?（）A
Copper Pass-thru Modules only support 1000Mb line speeds. B
Spanning Tree has been enabled on the Copper Pass-thru Module. C
The customer does not have the latest firmware loaded on the Copper Pass-thru Module. D
The customer is using LS21 Blades
热门标签
最新试卷
