网友您好， 请在下方输入框内输入要搜索的题目：
题目内容
（请给出正确答案）
多选题
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
A
Uplink Ethernet ports or border ports
B
Appliance ports
C
Server ports
D
Fabric ports
E
Backplane ports
F
vEth interfaces
G
A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
参考答案
参考解析
解析：
暂无解析
更多 “多选题A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）AUplink Ethernet ports or border portsBAppliance portsCServer portsDFabric portsEBackplane portsFvEth interfacesGA Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.” 相关考题
考题
What is the appliance port used to connect to in a Cisco Unified Computing System？（）A、 Fibre Channel storageB、 UCS C-Series serversC、 NFS storageD、 UCS chassisE、 Other fabric interconnect
考题
Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）A、LACPB、PAgPC、MCPC
考题
Which statement ab0ut VLANs in a Cisco UCS is true?（）A、Fabric interconnect can never participate in VTPB、Fabric interconnect supports ISL and 802.1Q trunkingC、The supported range of VLANs is auto-configured by UCSD、VLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
考题
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）A、 ServerB、 End deviceC、 NodeD、 HostE、 Virtual
考题
What is the use of an "all configuration" backup in Cisco UCS？（）A、 Can be used to migrate from a 6120 to a 6140 and retain the same service profilesB、 Can only be used on the fabric interconnect on which it was createdC、 Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster informationD、 Can be used to match firmware versions between 6120 and 6140 during a migration
考题
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）A、 Sending all broadcastsB、 Receiving all traffic from upstream switchesC、 Receiving broadcast trafficD、 Negotiating spanning tree with upstream switchesE、 Learning MAC addresses from upstream switches
考题
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）A、 Uplink Ethernet ports or border portsB、 Appliance portsC、 Server portsD、 Fabric portsE、 Backplane portsF、 vEth interfacesG、 A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
考题
Which port channel command is recommended for N1KV on Cisco UCS？（）A、 channel-group auto mode onB、 channel-group auto mode activeC、 channel-group auto mode on sub-group cdpD、 channel-group auto mode on sub-group manualE、 channel-group auto mode on mac-pinning
考题
Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）A、 End-host mode is synonymous with NPV mode.B、 In end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.C、 Making configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.D、 End-host mode is the default Fibre Channel switching mode.
考题
Which statements are true regarding the Cisco UCS fabric failover feature？ （）A、 FabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.B、 Gratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover. C、 Fabric failover can be used on vNICs and vHBAs.D、 Fabric failover is configured as part of the service profile.E、 Fabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
考题
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）A、 The fabric interconnect is in the end-host mode， and all uplink ports have failed.B、 The server port to which the adapter is pinned has failed.C、 A transient error has caused the link to fail.D、 The fabric interconnect is in the switch mode， and all uplink ports have failed.E、 The link for a network-facing host interface is missing.
考题
Where are SAN Port Channel is created in UCS Manager？（）A、 Under the Admin tab on the FIB、 Under the Server tab in the service profileC、 Under the SAN tab on each VSAND、 Under the Admin tab on the chassisE、 Under the SAN tab on the Fabric Interconnect
考题
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）A、 The fabric interconnects must be in end-host mode.B、 A pin group must be configured on the server tab in Cisco UCS Manager.C、 In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.D、 Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.E、 Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.
考题
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）A、 During the initial configuration from the consoleB、 Once the basic configuration has been appliedC、 To restore the configuration on a secondary fabric interconnectD、 To upgrade the firmware on a replacement fabric interconnect
考题
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）A、 Cisco UCS Manager 1.3（xx） or later and a pair of Nexus 2248 FEXesB、 Cisco UCS Manager 2.0（2xx） or later and a pair of Nexus 2232 FEXesC、 Two Cisco UCS 6100 Series or 6200 Series fabric interconnectsD、 Two RJ45 Ethernet cablesE、 The fabric interconnects must be in end-host mode
考题
单选题Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）A
ServerB
End deviceC
NodeD
HostE
Virtual
考题
多选题Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）AThe fabric interconnect is in the end-host mode， and all uplink ports have failed.BThe server port to which the adapter is pinned has failed.CA transient error has caused the link to fail.DThe fabric interconnect is in the switch mode， and all uplink ports have failed.EThe link for a network-facing host interface is missing.
考题
单选题When will an "all configuration" backup be imported into the Cisco UCS Manager？（）A
During the initial configuration from the consoleB
Once the basic configuration has been appliedC
To restore the configuration on a secondary fabric interconnectD
To upgrade the firmware on a replacement fabric interconnect
考题
多选题Which statements are true regarding the Cisco UCS fabric failover feature？ （）AFabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.BGratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover.CFabric failover can be used on vNICs and vHBAs.DFabric failover is configured as part of the service profile.EFabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
考题
单选题Which statement ab0ut VLANs in a Cisco UCS is true?（）A
Fabric interconnect can never participate in VTPB
Fabric interconnect supports ISL and 802.1Q trunkingC
The supported range of VLANs is auto-configured by UCSD
VLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
考题
单选题What is the use of an "all configuration" backup in Cisco UCS？（）A
Can be used to migrate from a 6120 to a 6140 and retain the same service profilesB
Can only be used on the fabric interconnect on which it was createdC
Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster informationD
Can be used to match firmware versions between 6120 and 6140 during a migration
考题
多选题Which two statements about end-host mode in SAN connectivity in a Cisco UCS environment are true？ （）AEnd-host mode is synonymous with NPV mode.BIn end-host mode， only hard pinning of vHBAs to Fibre Channel uplink ports is allowed.CMaking configuration changes between Fibre Channel switching mode and end-host mode is nondisruptive.DEnd-host mode is the default Fibre Channel switching mode.
考题
单选题In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）A
Sending all broadcastsB
Receiving all traffic from upstream switchesC
Receiving broadcast trafficD
Negotiating spanning tree with upstream switchesE
Learning MAC addresses from upstream switches
考题
单选题Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）A
LACPB
PAgPC
MCPC
考题
单选题Which port channel command is recommended for N1KV on Cisco UCS？（）A
channel-group auto mode onB
channel-group auto mode activeC
channel-group auto mode on sub-group cdpD
channel-group auto mode on sub-group manualE
channel-group auto mode on mac-pinning
考题
多选题What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）ACisco UCS Manager 1.3（xx） or later and a pair of Nexus 2248 FEXesBCisco UCS Manager 2.0（2xx） or later and a pair of Nexus 2232 FEXesCTwo Cisco UCS 6100 Series or 6200 Series fabric interconnectsDTwo RJ45 Ethernet cablesEThe fabric interconnects must be in end-host mode
考题
单选题What is the appliance port used to connect to in a Cisco Unified Computing System？（）A
Fibre Channel storageB
UCS C-Series serversC
NFS storageD
UCS chassisE
Other fabric interconnect
热门标签
最新试卷
